《IEEE-期刊论文word模版》由会员分享，可在线阅读，更多相关《IEEE-期刊论文word模版（6页珍藏版）》请在金锄头文库上搜索。
1、Manuscript received October 9, 2001. This work was supported in part by the U.S. Department of Commerce under Grant BS123456 . Paper titles should be written in uppercase and lowercase letters, not all uppercase. Avoid writing long formulas with subscripts in the title; short formulas that identify
2、the elements are fine . Do not write in the title. Full names of authors are preferred in the author field, but are not required. Put a space between authors initials. F. A. Author is with the National Institute of Standards and Technology, Boulder, CO 80305 USA . S. B. Author, Jr., was with Rice Un
3、iversity, Houston, TX 77005 USA. He is now with the Department of Physics, Colorado State University, Fort Collins, CO 80523 USA .T. C. Author is with the Electrical Engineering Department, University of Colorado, Boulder, CO 80309 USA, on leave from the National Research Institute for Metals, Tsuku
4、ba, Japan .Preparation of Papers for IEEE TRANSACTIONS and JOURNALSFirst A. Author, Second B. Author, Jr., and Third C. Author, Member, IEEEAbstractThese instructions give you guidelines for preparing papers for IEEE TRANSACTIONS and JOURNALS. Use this document as a template if you are using Microso
5、ft Word 6.0 or later. Otherwise, use this document as an instruction set. The electronic file of your paper will be formatted further at IEEE. Define all symbols used in the abstract. Do not cite references in the abstract. Do not delete the blank line immediately above the abstract; it sets the foo
6、tnote at the bottom of this column.Index TermsAbout four key words or phrases in alphabetical order, separated by commas. For a list of suggested keywords, send a blank e-mail to or visit nizations/pubs/ani_prod/keywrd98.txtI. INTRODUCTIONTHIS document is a template for Microsoft Word versions 6.0 o
7、r later. If you are reading a paper or PDF version of this document, please download the electronic file,TRANS-JOUR.DOC, from the IEEE Web site at so you can use it to prepare your manuscript. If you would prefer to use LATEX, download IEEEs LATEX style and sample files from the same Web page. Use t
8、hese LATEX files for formatting, but please follow the instructions in TRANS-JOUR.DOC or TRANS-JOUR.PDF.If your paper is intended for a conference, please contact your conference editor concerning acceptable word processor formats for your particular conference. When you open TRANS-JOUR.DOC, select
9、Page Layout from the View menu in the menu bar , which allows you to see the footnotes. Then, type over sections of TRANS-JOUR.DOC or cut and paste from another document and use markup styles. The pull-down style menu is at the left of the Formatting Toolbar at the top of your Word window . Highligh
10、t a section that you want to designate with a certain style, then select the appropriate name on the style menu. The style will adjust your fonts and line spacing. Do not change the font sizes or line spacing to squeeze more text into a limited number of pages. Use italics for emphasis; do not under
11、line. To insert images in Word, position the cursor at the insertion point and either use Insert | Picture | From File or copy the image to the Windows clipboard and then Edit | Paste Special | Picture . IEEE will do the final formatting of your paper. If your paper is intended for a conference, ple
12、ase observe the conference page limits. II. Procedure for Paper SubmissionA. Review StagePlease check with your editor on whether to submit your manuscript as hard copy or electronically for review. If hard copy, submit photocopies such that only one column appears per page. This will give your refe
13、rees plenty of room to write comments. Send the number of copies specified by your editor . If submitted electronically, find out if your editor prefers submissions on disk or as e-mail attachments.If you want to submit your file with one column electronically, please do the following:-First, click
14、on the View menu and choose Print Layout.-Second, place your cursor in the first paragraph. Go to the Format menu, choose Columns, choose one column Layout, and choose apply to whole document from the dropdown menu.-Third, click and drag the right margin bar to just over 4 inches in width.The graphics will stay in the second column, but you can drag them to the first column. Make the graphic wider to push out any text that may try to fill in next to the graphic.B. Final StageWhen you submit your final version , print it in two-
