《LED恒温加热平台说明书(英文版)》由会员分享，可在线阅读，更多相关《LED恒温加热平台说明书(英文版)（3页珍藏版）》请在金锄头文库上搜索。
1、Thermostatic Heater Illustration I. Item description: Adopted by original Yudian Automation PDI economic type temperature controller, its high-accuracy, operation is safe, simple, clear and convenience. Adopted by original high-quality AC solid-state relay, long lasting as 100 times of the common co
2、ntact relay. Adopted by multiple high-quality metal heating pipes, maintenance is convenience and low failure-rate. The aluminum top surface is high thermal conductivity, heat fast and evenly. The whole case is made by high-quality SUS304 stainless to ensure it against from rusted and peeling off in
3、 the usual condition. II. SpecfationPower Supply: 220V (50HZ);Controllable Temperature Range: Basic Type (Ordinary Temperature350); Elevated Temperature Type( Ordinary Temperature450), Ultra Temperature Type (Ordinary Temperature500), Each type of the item has Unitary Type (Model A), Splitting Type
4、(Model B) and Guardrail Type ( Model C).E，F。Item NO.Heat Generating Plate Spec.PowerNet WeightSET050550x50x20mm士1250W(MAX)3.5KgSET1010100x100x20mm士1500W (MAX)4.0 KgSET2015200X150X20MM士1 700W（MAX）5.5 kgSET2020200x200x20mm士1900W (MAX)5.2 KgSET3020300x200x20mm士11500W (MAX)6.5 KgSET3030300x300x20mm士1160
5、0W (MAX)7.0 KgSET3625360x250x20mm士11800W (MAX)8.5 KgSET4030400x300x20mm士12000W (MAX)12.5 KgSET5035500x350x20mm士12700W (MAX)21.3 KgSET6040600x400x20mm士13200W (MAX)22.5 KgSET8040800x400x20mm士13500W (MAX)25 KgIII. Application filed Electronic industrial bonding sealing and application heating. LED indu
6、strial aluminum base welding and maintenance mold core pre-heating Essential equipment at the laboratory in various industrials such as biology, genetics, medicine and environment etc.IV. Application Instruction Plug in the power and turn on the POWER switch while the RED indicator light constant li
7、ght, its means the device has being powered. Turn on the HEATING switch and the device is starting then, GREEN indicator light constant light, its means the device is heating up; sparkling means it has been into the constant temperature while workstation is being recycle heating up. Once it finish u
8、sing, please turn off the HEATING switch first and the device will be stopped heating, while the RED indicator light are still constant light in order to reminding the device are still working and please dont touch the work surface. Wait for the work surface being cool down (suggesting after an hour
9、) and torn off the POWER switch then.V. Attention: Voltage must be 220V, please use the 3 pole socket which is connect to the earth and with anticreeping switch as well. Please dont open the case or switch any wire position unless you are the specific operation. Hand touch is prohibited in case to a
10、void burn. Please unplug the power supply when the people away or device has being long term idle. Please keep the vent hole clean since the device has been cooperated with fan cooler, Please make sure it has unplugged from the power source when the fuse needs to be replaced for safety.VI. Control p
11、anel illustrationPVmeasurement value / model value displaydata position switchSVset value / model content value displaydata reducingOP1out putdata increasingAU1alarm 10model set ( enter)AU2alarm 2VII. Parameter Settingl Press the key “0” at few seconds to enter the following table:Nameillustrationse
12、tting rangeFactory DefultHIAMaximum alarm0-999999LOAMinimum alarm0-999-199HDAtolerance maximum alarm0-999999LOCparameter modify level0-2550(modify prohibited)l Set value setting: Press the key ， to modify the control value which is showing at the display window under the default situation, press the
13、 key for value reducing, press the key for value increasing, the dot sparkly with the number which position switched( sparkly like cursor). Press down for quick increase / reduce value, and the value will be speed up while the position of the dot rightward switch. Press the key to move and modify th
14、e position of the value (cursor). Press the key or to modify the value which is sparkly, control convenience.l Automatic adjustable (AT) operation, available with Automatic (AT) operating to confirm the PID adjustable parameter when use AI agronomical PID control. The AT parameter shows up after pre
15、ss the key at 2 seconds under the default situation. Press the key to modify the OFF to ON which is shown at the bottom display window, the Automatic Adjustable operation will be start by press the key “O” to confirm. At the same time, the letter “AT” will be sparking at the display window which is at the bottom of instrument panel, the result of the suitable PID parameter for the current condition will be counted automatically by the local micro CPU of the instrument panel, and it will be extermi
