《变频器错误列表(中文)》由会员分享，可在线阅读，更多相关《变频器错误列表(中文)（7页珍藏版）》请在金锄头文库上搜索。
1、变频器故障列表ConNo_Err(* Converter no error *) 变频器没有错误 ConErr001(* Converter unknown error *) 变频器未知故障ConErr002(* Time out error in SELFTEST, converter cant go out of failed state *) 自检超时,变频器无法退出故障状态ConErr003(* Precharge contactor not closed in PRECHARGE state *) 预充电时,预充电接触器没有吸合ConErr004(* Time out error i
2、n PRECHARGE state, no DC-bus voltage *) 预充电状态超时,没有直流母线电压ConErr005(* Time out error in SYNLINFIR, no synchronized to live voltage *) 电网同步超时,没有与实时电压同步ConErr006 (* Time out in CHANGECONTACTOR: Line contactor is not closed *)接触器变化超时:网侧接触器没有吸合ConErr007 (* Time out LOADDCBUS: DC-bus is not loaded *) 直流母线接
3、入超时:直流母线没有安装ConErr008(* Time out in SYNGENERATOR: Stator voltage is not synchronized *) 发电机同步超时:定子电压没有同步ConErr009(* Time out in SWITCHGENOFF, stator contactor didnt open *) 发电机停止开关超时,定子接触器没有打开ConErr010(* Time out in SWITCHGSCOFF, GSC current not set to 0 *) 发电机侧开关停止超时,电流无法清零ConErr011(* Out of I/O te
4、st, external demand *) 外部请求:I/O口检查ConErr012(* Out of PRECHARGE test, external demand *) 外部请求来自预充电检查ConErr013(* Out of LSV mode, external demand *) 外部请求:网侧电压模块ConErr014(* LS U mode test, precharge contactor not closed *) 网侧电压模块检测到预充电接触器没有吸合ConErr015 (* LS U mode test, DC bus not loaded *) 网侧电压模块检测直流母
5、线没有装好ConErr016(* LS U mode test, unknown state *) 网侧电压检查未知状态ConErr017(* Out of LS I mode, external demand *) 外部请求:网侧电流模块ConErr018(* LS I mode test, precharge contactor not closed *) 网侧电流模块检查预充电接触器没有吸合ConErr019(* LS I mode test, DC bus not loaded *) 网侧电流模块检测直流母线没有装好ConErr020(* LS I mode test, unknown
6、s state *) 网侧电流模块检查到未知状态ConErr021(* Out of LS Syn mode,external demand *) 外部请求:网侧同步模块ConErr022 (* LS SYN mode test, precharge contactor not closed *) 网侧同步检查预充电接触器没有吸合ConErr023(* LS SYN mode test, DC bus not loaded *) 网侧同步检查直流母线没有装好ConErr024(* LS SYN mode test, voltage not synchronized to Line voltag
7、e *) 网侧同步检查,电压没有与网侧电压同步ConErr025(* LS SYN mode test, line contactor not closed *) 网侧同步检查电网接触器没有吸合ConErr026(* LS SYN mode test, DC bus not loaded *) 网侧同步检查直流母线没有装好ConErr027(* LS SYN mode test, unknown state *) 网侧同步检查未知状态ConErr028(* Out of GS U mode, external demand *) 外部请求:发电机侧电压模块ConErr029(* GS U mo
8、de, precharge contactor not closed *) 发电机电压模块,预充电接触器没有吸合ConErr030 (* GS U mode, DC bus not loaded *) 发电机侧电压模块,直流母线没有装好ConErr031(* GS U mode, unknowns state *) 发电机侧电压模块,未知状态ConErr032(* Out of GS I mode, external demand *) 外部请求:发电机侧电流模块ConErr033 (* GS I mode, precharge contactor not closed *) 发电机侧电流模块
9、,预充电接触器没有吸合ConErr034(* GS I mode, DC bus not loaded *) 发电机侧电流模块,直流母线没有装好ConErr035(* GS I mode, unknown state *) 发电机侧模块,未知状态ConErr036(* Out of CB test, external demand *) 外部请求:Crowbar检查ConErr037(* Crowbar test, precharge contactor not closed *) Crowbar检查预充电接触器没有吸合ConErr038(* Crowbar test, DC bus not
10、*) Crowbar检查,直流母线没有装好ConErr039(* Crowbar test, rotor magnetization current not enough *) Crowbar检查,转子励磁电流不够ConErr040(* Crowbar has triggered *) Crowbar被触发ConErr041(* Crowbar test, unknown state *) Crowbar检查未知状态ConErr042(* Out of Communication test, external demand *) 外部请求:通信检查ConErr043(* Out of Heat
11、run test, external demand *) 外部请求:加热器运行检查ConErr044(* Heatrun test, precharge contactor not closed *) 加热器运行检查,预充电接触器不吸合ConErr045(* Heatrun test, DC bus not loaded *) 加热器运行时,直流母线没有装好ConErr046(* Heatrun test, LSC voltage not synchronized to Line voltage *) 加热器运行检查,网侧变频器电压与电网电压不同步ConErr047(* Heatrun tes
12、t, Line contactor not closed *) 加热器运行检查,网侧接触器没有吸合ConErr048(* Heatrun test, DC bus not loaded *) 加热器运行检查,直流母线没有装好ConErr049(* Heatrun test, blocked in substate 7 *) 加热器运行检查,锁定在亚状态7ConErr050 (* Heatrun test, blocked in substate 8 *) 加热器运行检查,锁定在亚状态8ConErr051(* Heatrun test, unknown state *) 加热器运行检查，未知状态
13、ConErr052(* Demanded state setting, precharge *) 设定要求状态:充电ConErr053(* Demanded state setting, armed *) 设定要求状态:供电ConErr054(* Demanded state setting, GSC on *) 设定要求状态:发电机侧变频器开启ConErr055 (* Demanded state setting, GSC syn *) 设定要求状态:发电机侧变频器同步ConErr056(* Demanded state setting, stator contactor *) 设定要求状态
14、:定子接触器ConErr057 (* Demanded state setting, production *) 设定要求状态:发电ConErr058(* State machine, unknown state *) 机器状态,未知059098 无故障代码ConErr099(* Grid problem *) 电网问题ConErr100(* Encoder zero pulse missing *) 编码器缺失零脉冲ConErr101(* current regulator LSC not set well *) 网侧变频器节流器未调整好(网侧接触器3相错误)ConErr102(* Line
15、 contactor state error *) 网侧接触器状态有错误ConErr103(* DSPA remote parameter access failed *) 变频器DSP-A侧远程参数存取失败ConErr104(* Crowbar has triggered *)Crowbar被触发ConErr105(* line failure undervoltage *) 电网欠电压ConErr106(* line failure overvoltage *) 电网过电压ConErr107(* Small overvoltage DC bus in production *) 发电时直流母线微过压ConErr108(* Small DC bus overvoltage caused by line instability *) 电网电压不稳定造成直流母线微过压ConErr109 (* Line over frequency *) 电网电压频率过高ConErr110(* Line under frequency *) 电网电压频率过低Co
