《路由器的链路捆绑【链路聚合】》由会员分享，可在线阅读，更多相关《路由器的链路捆绑【链路聚合】（18页珍藏版）》请在金锄头文库上搜索。
1、RA路由器上配置Routerenable /进入特权模式Router#config /进入配置模式Router_config#hostname RA /更改设备名称RA_config#int serial 0/1 /进入s0/1串口RA_config_s0/1#default interface serial 0/1RA_config_s0/1#Jan 1 00:40:12 Line on Interface Serial0/1, changed to downJan 1 00:40:13 Line on Interface Serial0/1, changed to up【重置端口，恢复出厂
2、设置】RA_config_s0/1#encapsulation pppRA_config_s0/1#Jan 1 00:43:29 Line on Interface Serial0/1, changed state to up【封装PPP协议】RA_config_s0/1#physical-layer speed 64000【设置端口速率，波特率】RA_config_s0/1#ppp multilink /启用多链路PPPRA_config_s0/1#multilink-group 1 RA_config_s0/1#Jan 1 00:45:03 Line on Interface Multil
3、ink1, changed state to up【加入组1】RA_config_s0/1#exit /退出RA_config#int serial 0/2RA_config_s0/2#default interface serial 0/2RA_config_s0/2#Jan 1 00:46:10 Line on Interface Serial0/2, changed to downJan 1 00:46:11 Line on Interface Serial0/2, changed to upRA_config_s0/2#encapsulation pppRA_config_s0/2#J
4、an 1 00:46:22 Line on Interface Serial0/2, changed state to up speed - 端口速率RA_config_s0/2#physical-layer speed 64000RA_config_s0/2#ppp multilink RA_config_s0/2#multilink-group 1RA_config_s0/2#exitRA_config#interface multilink 1 /建立multilink1RA_config_m1#ip address 192.168.0.1 255.255.255.252【设置IP地址和
5、掩码】RA_config_m1#ppp multilink /启用多链路pppRA_config_m1#multilink-group 1 /加入组1RA_config_m1#exit /退出在RB路由器上配置Routerenable Router#configRouter_config#hostname RB RB_config#int serial 0/1RB_config_s0/1#default interface serial 0/1RB_config_s0/1#Jan 1 00:52:48 Line on Interface Serial0/1, changed to downJa
6、n 1 00:52:49 Line on Interface Serial0/1, changed to upRB_config_s0/1#encapsulation pppRB_config_s0/1#Jan 1 00:53:02 Line on Interface Serial0/1, changed state to upJan 1 00:53:04 Line protocol on Interface Serial0/1, changed state to upRB_config_s0/1#physical-layer speed 64000RB_config_s0/1#ppp mul
7、tilink RB_config_s0/1#Jan 1 00:53:27 Line protocol on Interface Serial0/1, changed state to downJan 1 00:53:27 Line protocol on Interface Serial0/1, changed state to upRB_config_s0/1#multilink-group 1RB_config_s0/1#Jan 1 00:53:39 Line protocol on Interface Serial0/1, changed state to downJan 1 00:53
8、:39 Line on Interface Multilink1, changed state to upJan 1 00:53:39 Line protocol on Interface Serial0/1, changed state to upRB_config_s0/1#exitRB_config#int serial 0/2RB_config_s0/2#default interface serial 0/2RB_config_s0/2#Jan 1 00:54:07 Line on Interface Serial0/2, changed to downJan 1 00:54:07
9、Line on Interface Serial0/2, changed to upRB_config_s0/2#encapsulation pppRB_config_s0/2#Jan 1 00:54:37 Line on Interface Serial0/2, changed state to upRB_config_s0/2#physical-layer speed 64000RB_config_s0/2#ppp multilink RB_config_s0/2#Jan 1 00:55:07 Line protocol on Interface Serial0/2, changed st
10、ate to downJan 1 00:55:08 Line protocol on Interface Serial0/2, changed state to upRB_config_s0/2#multilink-group 1RB_config_s0/2#Jan 1 00:55:18 Line protocol on Interface Serial0/2, changed state to downJan 1 00:55:18 Line protocol on Interface Serial0/2, changed state to upRB_config_s0/2#exitRB_co
11、nfig#int multilink 1RB_config_m1#ip address 192.168.0.2 255.255.255.252RB_config_m1#ppp multilink RB_config_m1#multilink-group 1RB_config_m1#exitRB_config#show ip int briInterface IP-Address Method Protocol-Status Async0/0 unassigned manual downFastEthernet0/0 unassigned manual downGigaEthernet0/3 u
12、nassigned manual downGigaEthernet0/4 unassigned manual downGigaEthernet0/5 unassigned manual downGigaEthernet0/6 unassigned manual downSerial0/1 unassigned manual downMultilink1 192.168.0.2 manual up Serial0/2 unassigned manual downRB_config#exitRB#Jan 1 00:56:48 Configured from console 0 by UNKNOWN
13、RB#ping 192.168.0.1PING 192.168.0.1 (192.168.0.1): 56 data bytes!- 192.168.0.1 ping statistics -5 packets transmitted, 5 packets received, 0% packet lossround-trip min/avg/max = 20/22/30 ms【证明做成了，下面加个chap认证，密码123456】RB_config#RB_config#interface multilink 1 /进入multilink口RB_config_m1#ppp authenticati
14、on chap /启用chap认证RB_config_m1#Jan 1 00:58:23 Line protocol on Interface Serial0/1, changed state to downJan 1 00:58:23 Line protocol on Interface Serial0/2, changed state to downRB_config_m1#ppp chap hostname RB /设置CHAP主机名RB_config_m1#exit /退出RB_config#aaa authentication ppp default local /做ppp的3a认证RB_config#username RA password 0 123456【创建对端用来验证CHAP的用户名和密码】RB_config#show running-config 正在收集配置.当前配置:!version 1.3.3Hservice timestamps log dateservice timestamps debug date
