《检具设计方案中英文资料》由会员分享，可在线阅读，更多相关《检具设计方案中英文资料（17页珍藏版）》请在金锄头文库上搜索。
1、JBM Auto SystemB515B515B515B515Checking Checking Checking Checking Fixture Phase IIFixture Phase IIFixture Phase IIFixture Phase II HuangyanHuangyanHuangyanHuangyan11/6/20111Date 15-10-11B515 检具-黄岩JBM Auto System11/6/20112Swivel form check template min two numbers Provided至少应有两个样板刀JBM Auto System11/
2、6/20113Max line 3mm from nominal lineMin line should be “Tolerance specified in cad”PartNominal lineTrim line marking for all checking fixture名义修边线板件距离名义修边线 3mm的最大修边线最小修边线的公差应 符合图纸的要求。所有检具划修边线JBM Auto System11/6/20114ABA- You provided diamond pin it is not acceptable please provide tapper pin with m
3、inimum and maximum tolerance B- You provided straight pin instead of that please provide tapper pin with minimum and maximum tolerance as shown in the figureMax toleranceMin tolerancePartRound pin最小公差板件最大公差圆销1.你方采用菱形销，是不可以的，请采用锥形销，并给出最大和 最小公差。2.不要采用直销，请采用锥形销，并给出最大和最小公差。JBM Auto System11/6/20115Part
4、No 8V21-A18A344 Up date the changes and sent me the updated data then Please Go for manufacturingProvide car line with150mm pitch, part clamping as per LD dataProvide Swivel form check template min two numbers. See slide NO 2至少应有两个样板刀。参 照图片2应有汽车坐标，并以 150mm 为间距，零件 夹持应符合零件检测 的要求。将修改后的设计发送给我们，然后 进行制造。J
5、BM Auto System11/6/20116Part No CN15- N40308 Up date the changes and sent me the updated data then Please Go for manufacturingProvide car line with150mm pitch, part clamping as per LD dataProvide Swivel form check template min two numbers. See slide no 2将修改后的设计发送给我们，然后 进行制造。至少应有两个样板刀。参 照图片2应有汽车坐标，并以
6、 150mm 为间距，零件 夹持应符合零件检测 的要求。JBM Auto System11/6/20117Part No CN15-N40324-AUp date the changes and sent me the updated data then Please Go for manufacturingProvide car line with150 mm pitch, Provide Swivel form check template min two numbers. See slide no 2至少应有两个样板刀。参 照图片2应有汽车坐标，并以 150mm 为间距 。将修改后的设计
7、发送给我们，然后 进行制造。JBM Auto System11/6/20118This land should be increased by 3 mm so that This land should be increased by 3 mm so that variation in burring (Flange) can be measured 该区域高度加高3mm ，以便于能够检测到 毛刺（翻边）。JBM Auto System11/6/20119Part No CN15-N1407Up date the changes and sent me the updated data the
8、n Please Go for manufacturingProvide car line with150mm pitch, Provide Swivel form check template min two numbers. See slide no 2至少应有两个样板刀。参 照图片2应有汽车坐标，并以 150mm 为间距 。将修改后的设计发送给我们，然后 进行制造。JBM Auto System11/6/201110Part No CN15-N43881Up date the changes and sent me the updated data then Please Go for
9、manufacturingRemove this relive. 将修改后的设计发送给我们，然后 进行制造。去除该让开JBM Auto System11/6/201111Part No CN15-18D317Up date the changes and sent me the updated data then Please Go for manufacturingPart clamping as per LD dataProvide Swivel form check template min two numbers. See slide no 2将修改后的设计发送给我们，然后 进行制造。
10、零件夹持应符合零件检测要求至少应有两个样板刀。参 照图片2JBM Auto System11/6/201112Checking fixture Part No CN15-N02030Up date the changes and sent me the updated data then Please Go for manufacturingDirection of the checking fixture to be changed将修改后的设计发送给我们，然后 进行制造。检具检具方向应修改JBM Auto System11/6/201113Part No CN15-16H004Up dat
11、e the changes and sent me the updated data then Please Go for manufacturingProvide car line with150mm pitch, Provide Swivel form check template min two numbers. See slide no 2将修改后的设计发送给我们，然后 进行制造。应有汽车坐标，并以 150mm 为间距 。至少应有两个样板刀。参 照图片2JBM Auto System11/6/201114Part No CN15-N40014Up date the changes an
12、d sent me the updated data then Please Go for manufacturingProvide car line with150mm pitch, Provide Swivel form check template min two numbers. See slide no 2将修改后的设计发送给我们，然后 进行制造。应有汽车坐标，并以 150mm 为间距 。至少应有两个样板刀。参 照图片2JBM Auto System11/6/201115Part No CN15-1A457Please Go for manufacturingProvide car line with 50mm pitch, 请继续进行制造应有汽车坐标，并以 50mm 为间距 。JBM Auto System11/6/201116Part No CN15-N42940Please Go for manufacturingProvide car line with 50mm pitch, 请继续进行制造应有汽车坐标，并以 50mm 为间距 。JBM Auto System11/6/201117Part No CN15-1412Please Go for manufacturing请继续进行制造
