《模具精各部件的英文名称12》由会员分享，可在线阅读，更多相关《模具精各部件的英文名称12（5页珍藏版）》请在金锄头文库上搜索。
1、This trial version can use only a part of item.Runner SystemIn this chapter, you will learn about the functions, characteristics, and shapes of the sprue, runner, and gate.The molten plastic injected from the injector nozzle will go through a sprue (sprue bush), a runner, and a gate and fill up in t
2、he cavity. As the temperature of molten plastic is lowered while going through the sprue and runner, the viscosity will rise; therefore, the viscosity is lowered by shear heat generated when going through the gate to fill the cavity. Sprue A sprue is a channel through which to transfer molten plasti
3、c injected from the nozzle of the injector into the mold. It is a part of sprue bush, which is a separate part from the mold. Runner A runner is a channel that guides molten plastic into the cavity of a mold. Gate A gate is an entrance through which molten plastic enters the cavity. The sprue, the r
4、unner, and the gate will be discarded after a part is complete. However, the runner and the gate are important items that affect the quality or the cost of parts.Gate The gate is categorized into restrictive gate, which narrows the entrance, and nonrestrictive gate, which does not narrow the entranc
5、e.The gate has the following functions: Restricts the flow and the direction of molten plastic. Simplifies cutting of a runner and moldings to simplify finishing of parts. Quickly cools and solidifies to avoid backflow after molten plastic has filled up in the cavity. Restrictive Gate A restrictive
6、gate has a narrow entrance to the cavity to restrict the amount of molten plastic in order to improve filling in the cavity. The restrictive gate has the following characteristics. oGenerates shear heat by going through the narrow gate, raising the temperature of molten plastic and improving the fil
7、ling in the cavity. oReduces residual stress, and thus reduces part defect such as warp. oAs the cooling solidification time is shortened, molding cycle is also shortened. oAs the gate trace is less, it is possible to complete finishing process in a short time. The restrictive gate has the following
8、 types. Side Gate Submarine Gate 丂丂(Tunnel Gate) The most common gate. Put to the side of parts. The gate trace will be left. Often used for the structure with more than two cavities. The gate will be automatically cut off during mold opening. The position is flexible (front, side, or back of parts)
9、. The gate needs to be thought about not to be left inside the cavity.Pin Point Gate Fan Gate Suitable for molding multiple parts. The position is relatively flexible. The structure is complicated due to three plate method of die. Suitable for large and flat plate parts. Finishing is difficult and c
10、ost is high due to the wide gate. The gate trace will be left. Film Gate Valve Gate Suitable for thin plate parts. Finishing is difficult and cost is high due to the wide gate. The gate trace will be left.The valve of the gate opens the gate according to injection timing. Sprue and runner will not b
11、e discharged due to hot runner method. Put to either the front or the back surface of parts. Nonrestrictive Gate A nonrestrictive gate involves a method in which molten plastic fills up in the cavity directly from the sprue. The nonrestrictive gate has the following characteristics. oReduces the los
12、s of injecting pressure due to direct cavity filling from the sprue. oLess molding material because there is no runner . oThe simple mold structure reduce the cost and produces a mold with less trouble. oIt is likely that residual stress is generated and parts have crack. The nonrestrictive gate has
13、 the following type. Direct Gate The sprue plays the role as gate. Put on the front or back side of parts. The gate trace will be left. Determining Gate Position Point 1 Set a gate position where molten plastic finished filling up in each cavity simultaneously. Same as multiple points gate. Point 2
14、Basically set a gate position to the thickest area of a part. This can avoid sink marks due to mold shrinkage . Point 3 Set a gate position to an unremarkable area of part or where finishing process can be easily done. Point 4 Avoid injecting from the direction where the air in the cavity or the gas generated from molten plastic is inclined to accumulate. Point 5 Fill up molten plastic using the wall surface in order not to generate jetting.
