《外贸diy个性组装型大尺寸桌面级民用3d打印机创想三维cr-10 英文说明书v2》由会员分享，可在线阅读，更多相关《外贸diy个性组装型大尺寸桌面级民用3d打印机创想三维cr-10 英文说明书v2（16页珍藏版）》请在金锄头文库上搜索。
1、CR-10 Series 3D Printer This guide is for the CR-10 Series of 3D printers. It is also applicable for the CR-10S/CR-10 S4/CR-10 S5. Because of software/hardware upgrades and model differences, new revisions may not be listed in this guide. Detailed instructions for use are available on the SD card.V1
2、.12.1Notes1.Do not use the Printer in any way other than described herein to avoid personal injury or property damage. 2.Do not place the Printer near flammables, explosives or heat sources. It is best to place it in a well- ventilated, low-dust environment. 3.Do not expose the Printer to violent vi
3、bration or any unstable environment. This will cause poor print quality. 4.The filaments recommended by the manufacturer are preferred as to avoid clogging in the hot end and/or Printer damage. 5.Do not use any other power cable than the one supplied. Use a grounded three-prong power outlet. 6.Do no
4、t touch the nozzle or hot bed during printing. Keep hands away from machine while in use to avoid burns or personal injury. 7.Do not wear gloves or loose clothing when operating the Printer. These loose articles can become caught in moving parts and cause personal injury or Printer damage. 8.Clean o
5、ff filament from the nozzle tip with the provided pliers before the nozzle cools. Do not touch the nozzle directly. This can cause personal injury. 9.Clean the Printer frequently. With the machine powered off, clean the printer body with a dry cloth to remove dust, adhered printing materials and for
6、eign objects on guide rails. Use glass cleaner or isopropyl Alcohol to clean the print surface before every print for consistent results. 10. Children under 10 years of age should not use the Printer without supervision.Preface1.Introduction .1 2.Package Contents .2 3.Assembly 3 4.LCD Menu 5 5.Filam
7、ent Loading .6ContentsDear consumers, Thank you for choosing our products. For the best experience, please read the instructions before operating the Printer. Our 3D team is always ready to provide you with assistance. Please contact us via the phone number or e-mail address provided at the end when
8、 you encounter any problem with the Printer. For a better experience in using our product, you may learn how to use the Printer in the following ways: 1. View the accompanied instructions and videos on the SD card. 2. Visit our official website at . You will find relevant software/hardware informati
9、on, contact details and operation and maintenance instructions on the website.6.Bed Leveling .7 7.Software Installation .8 8.Preparing to Print9 9.Trouble-shooting 10 10. After-Sales Services 111. Introduction11.Control Box 2.Spool Holder 3.Nozzle Assembly 4.Gantry Frame 5.Print Surface6. Base Frame
10、 7. SD Slot and USB Port 8. Voltage Selection 9. Control Knob 10. Display11. X Stepper 12. X Limit Switch 13. Extruder (E) Stepper 14. Y Stepper 15. Y Limit Switch16. Z Stepper 17. Z Limit Switch 18. Nozzle Assembly Connection 19. Hot Bed Connection 20. Power Cable Connection工具包清单2. Package Contents
11、序号配图配件名称数量1 Spool Holder w/ Nuts12 Spool Holder Bracket13 Sample Filament (200g)14 Thumb Screws35 T-Bracket (Right)16 T-Bracket and Z Limit Switch (Left)1序号配图配件名称数量7 M5X25 Bolt and Lock Washer4 sets8 Power Cable19 USB Cable110 SD Card and Card Reader 111 PTFE Tubing(spare part)112 Nozzle Cleaner1序号配
12、图配件名称数量13 Scraper 114 Diagonal Pliers115 Hex keys, Wrench and Screwdriver1 set16 Cable Ties1 bundle17 Spare Parts118 Decorative Trim12Base FrameGantry FrameControl BoxTool Kit3. Assembly3Install the Gantry FrameScrew in and fasten two M5X25 BoltsInstall left side T- Bracket, making sure T-Nuts are p
13、roperly installed.Install right side T- BracketScrew in and fasten two M5X25 BoltsNote: Make sure that the nut for profile has been turned by 90 before fastening the T-shaped fixing block.Attach the Z CouplersInsert the Teflon pipe into the quick connector4 Install the Spool Holder and Bracket Insta
14、ll the Decorative TrimAttach the Bracket with two thumb screws.Attach Spool Holder with included Nuts FinishedInstall the Decorative Trim into the grooves, starting from one end.Cut off the excess material with the diagonal pliersAttach the Decorative Trim to all parts needing to be decorated.* The
15、Decorative Trim is available in various colors. The pictures above are for reference only.Extruder (E) Stepper X Stepper and Limit SwitchY Stepper and Limit SwitchZ Stepper and Limit Switch WiringConnect the Stepper Motors according to the yellow labels on the 6pin (4-wire) side.Connect the Limit Sw
16、itches according to the yellow labels on the 3pin (2-wire) side. Select the correct input voltage to match your local mains (220V or 110V) Damage can occur if voltage is set incorrectly Make sure the power cable is connected.4Connect the aviation connectors to the ports with corresponding pinsYour 3D printer is n
