《SAEJ457v001SAE J 457 SAE 锻制铝合金的化学组成，机械性能限值和尺寸公差》由会员分享，可在线阅读，更多相关《SAEJ457v001SAE J 457 SAE 锻制铝合金的化学组成，机械性能限值和尺寸公差（3页珍藏版）》请在金锄头文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.QUESTIONS REGARDING THIS DOCUMENT: (412) 772-8512 FAX: (412) 776-0243 TO PLACE A DOCUME
3、NT ORDER; (412) 776-4970 FAX: (412) 776-0790 SAE WEB ADDRESS http:/www.sae.orgCopyright 1991 Society of Automotive Engineers, Inc. All rights reserved.Printed in U.S.A.SURFACE VEHICLE400 Commonwealth Drive, Warrendale, PA 15096-0001STANDARDSubmitted for recognition as an American National StandardJ4
4、57REV. FEB91Issued1911-06 Revised1991-02Superseding J457 AUG85(R) CHEMICAL COMPOSITIONS, MECHANICAL PROPERTY LIMITS, AND DIMENSIONAL TOLERANCES OF SAE WROUGHT ALUMINUM ALLOYS1.ScopeThis SAE Standard for wrought aluminum alloys provides sources of chemical and mechanical property data for a considera
5、ble range of alloys with varying properties, structures, and applications.2.References2.1Applicable PublicationsThe following publications form a part of this specification to the extent specified herein. The latest issue of SAE publications shall apply.2.1.1SAE PUBLICATIONSAvailable from SAE, 400 C
6、ommonwealth Drive, Warrendale, PA 15096-0001.SAE J454General Data on Wrought Aluminum Alloys SAE J993Alloy and Temper Designation Systems for Aluminum2.1.2ANSI PUBLICATIONSAvailable from ANSI, 11 West 42nd Street, New York, NY 10036.ANSI H35.1Alloy and Temper Designation Systems for Aluminum ANSI H3
7、5.2Dimensional Tolerances for Aluminum Mill Products2.1.3ASTM PUBLICATIONSAvailable from ASTM, 1916 Race Street, Philadelphia, PA 19103.ASTM B 209Specification for Aluminum-Alloy Sheet and Plate ASTM B 210Specification for Aluminum-Alloy Drawn Seamless Tubes ASTM B 211Specification for Aluminum-Allo
8、y Bars, Rods, and Wire ASTM B 221Specification for Aluminum-Alloy Extruded Bars, Rods, Shapes, and Tubes ASTM B 234Specification for Aluminum-Alloy Drawn Seamless Tubes for Condensers and Heat Exchangers ASTM B 236Specification for Aluminum Bar for Electrical Purposes (Bus Bar) ASTM B 241Specificati
9、on for Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube ASTM B 247Specification for Aluminum-Alloy Die and Hand Forgings ASTM B 308Specification for Aluminum-Alloy Standard Structural Shapes, Rolled or ExtrudedSAE J457 Revised FEB91-2-3.Specification of Wrought Aluminum AlloysThe Aluminum Ass
10、ociation publishes a manual entitled Aluminum Standards and Data which includes the specified limits registered for the chemical composition and mechanical properties of standard aluminum alloys commercially available in the wrought product forms shown in Tables 2 and 3 of SAE J454.NOTEThe Aluminum
11、Association Inc. standards may be obtained at no cost to users of aluminum from The Aluminum Association, 900 19th Street, N.W., Washington, DC 20006.4.Chemical Composition LimitsThe chemical composition limits for each wrought aluminum alloy are registered in accordance with the designation system
12、presented in ANSI H35.1 and SAE J993. The chemical composition limits are tabulated by alloy and are the same for all wrought product forms in which the alloy is available. In addition, the tabulation is by alloy components in the case of alclad sheet, plate, and tubular products.5.Mechanical Proper
13、ty LimitsThe specified mechanical property limits are established for each wrought product; that is, sheet, plate, drawn tube, extruded shapes, pipe and extruded tube, rolled shapes, rod, bar, wire, and die forgings.6.Dimensional TolerancesThe dimensional tolerances to which aluminum alloy mill prod
14、ucts are commercially produced are in accordance with the latest revision of the ANSI H35.2. For sizes outside commercial limits, the tolerance shall be as agreed upon by the supplier and purchaser.7.Standards for Chemical Composition and Mechanical Property LimitsThe American Society for Testing an
15、d Materials Standards and American National Standards in Table 1 contain the specified chemical composition limits, mechanical property limits, and material designations for each of the wrought products listed:8.Notes8.1Marginal IndiciaThe (R) is for the convenience of the user in locating areas whe
16、re technical revisions have been made to the previous issue of the report. If the symbol is next to the report title, it indicates a complete revision of the report.PREPARED BY THE SAE WROUGHT ALUMINUM COMMITTEETABLE 1STANDARDS FOR CHEMICAL COMPOSITION AND MECHANICAL PROPERTY LIMITSTitleASTM B 209Specification for Aluminum-Alloy Sheet and PlateASTM B 210Specification for Aluminum-Alloy Drawn Seamless TubesASTM B 211Specification for Aluminum-Alloy Bars, Rods, and
