《抹胸打印版{服装剪裁}》由会员分享，可在线阅读，更多相关《抹胸打印版{服装剪裁}（14页珍藏版）》请在金锄头文库上搜索。
1、(Afternoon) Tea Top By Karin Arver, IchigoGirl 2009-08-27 Pattern and instructions for fitted top with pleated detail. Printing the pattern: I made the pages in A4, but they should come out right on other sizes of paper too if you make sure to choose “dont scale” when you print it. Measure the test-
2、square if youre not sure. Size: Equivalent to Burdastyle sz 36 (In the shops I always buy size 34 though, so check your measurements to mine to be sure about the size). This pattern fits me (84cm bust, 67cm waist and 90cm hips, 165 cm tall, bra size 70B = 32B). The top is fitted, so you may need to
3、alter the pattern to fit if your measurements differ from mine, but it should be a bit forgiving since the top-part is gathered. Alter the body in the side-seams and/or darts if necessary. Alter the top front in the middle of each cup and the back top-part in the same part as youve altered the botto
4、m back-part. Dont forget to alter the facing (pieces 5 and 6) if you alter the top-part of the pattern (pieces 3 and 4). Remember that if you need the top to be for example 2cms wider, you only need to add 0,5cms to the side seam or middle of each pattern-piece, as that adds up to 2cm in total. You
5、need: Zipper or hook-and-eye-ribbon. (about 40cms long, depending on how long you want the top to be). Material for the top (about 60cms should be enough, depending on fabric width). Satin for pleated detail, (4cm wide x about 2ms long) Thread Recommended fabrics: Light wool, cotton, silk and silk-,
6、 cotton- or wool-blends. Unsuitable for knits. How to make the pleat: Cutting the material: All pattern pieces include 1.5 cms seam allowance, as indicated on pattern. 1. Bodice front (cut 1, on fold) 2. Bodice back (cut 2) 3. Front yoke (cut 1, on fold) 4. Back yoke (cut 2) 5. Front facing (cut 1,
7、on fold) 6. Back facing (cut 2) 7. Pleat detail (cut 1 strip of satin, 4cms wide, with fabric grain running lengthwise, to about 2,5x the length of the top edge of the top = about 2ms) Preparation: Place pattern pieces on fabric, making sure grainline is correct. Cut pieces and transfer all markings
8、 to fabric. Apply lightweight interfacing to the wrong sides of the facings (if the fabric is loose or very thin and needs more stability). Dont interface the seam-allowances. Sewing: 1. Finish the edges of all pieces (zig-zag). 2. Stitch the darts on the front piece and back piece. 3. Stitch double
9、 lines for gathering about 3mm apart, just outside the side-seam-marks of the top part of the front yoke (piece no3). Use long stitches (5-6). Stitch two equivalent lines on each side of the center of the front yoke. 4. Pin the front yoke to the back yoke (the side-seams). Gather the side-seam-gathe
10、rs on the front yoke to the same length as the back yoke piece side, tie a knot a each end of the gathers and distribute the gathers along the seam, pin and stitch. Remove the gathering-seams. 5. Pin the bottom piece and the front piece side-seams (piece no 1 and 2) and stitch. 6. Pin the bottom of
11、the front yoke (piece no 3) and back yokes (piece no 4) to the top of the bodice front- and back piece (piece no1 and no 2) right sides facing and stitch. Make sure all the seams match up (the side-seams and the yoke/bottom-piece seams). 7. Gather the center front yoke gather to 5cms, tie knots at e
12、ach end of the gather to keep the threads from slipping and carefully stitch back and forth along the gather (in between the gathering-stitch-lines) a few times, between the two gather- threads. Remove the gathering-threads (the basting). 5. Make the pleated ruffle for the top (Instructions here: pl
13、eated-trim) and pin it to the top of the front- pieces (the yoke-part), starting in the center front, in between the facing and the back pieces (make sure everything goes the right way after sewing, right sides should face each other with the pleat in between!). Stitch and turn the right way, so tha
14、t the pleated ruffles top part sticks out above the facing and fabric. 10. Press seam allowances open (not necessary next to the gathers). Also press a fold along the seam-allowances of the center back, to make it easier to sew the zipper or hook-and-eye-ribbon. 11. Pin the zipper or hook-and- eye-r
15、ibbon to the folded edge of the center back-pieces. Make sure it looks neat where the trim meets the zipper/hook/eye-ribbon. You can fold the end of the trim underneath the facing to hide the end if necessary. Stitch as close to the zippertooth/hooks and eyes as possible. 12. Top stitch along the pl
16、eated ruffle, on the right side, a couple of mms from the edge of the tops fabric/the trim. 13. Hem as desired (I used an invisable hem-stitch on my sewing machine, but you could just fold and stitch as you would on a blouse). 14. Secure the facing to the side-seams, center-front and if necessary center back with a few stitches (by hand). Finished! (Just one more thing. please please please upload images of your creation on Burdastyle!)
