《服装工艺设计中英文对照表》由会员分享，可在线阅读，更多相关《服装工艺设计中英文对照表（16页珍藏版）》请在金锄头文库上搜索。
1、-服装中英文对照表服装中英文对照表请注意生产如下、Pls pay attention for production as below抽查、MEIYUE inspected夹圈捆条扭皱不均、puckering and twisting at armhole piping /缝骨线阔窄、uneven topstitch on seam缝骨打褶、pleated on seam夹圈起皱、fullness at sleeve armhole insertion缝骨起皱、seam puckering前幅 front 后幅 back 面料 fabric 里料 lining后筒位不直，谷皱不平服、back s
2、lit not straight,crooking筒脚位长短、襟边有长短、uneven placket length后领筒位上下咀、hi low back slit襟边左右长短,襟脚圆角位不圆顺 unbalance lapel length, lapel corner not smooth前后幅脚边不平行、front and back bottom not leveling装领前领窝缩皱/领咀不圆顺凸咀 puckering at front neck seam, neckband end not align neck seam下级领脚扭皱不平服、puckering at collar band
3、领圈位皱不平服、Collar a wrinkle is not flat领型样子不均匀、collar shape is not pressing领尖左右长短不对称、asymmetrical collar point领尖角爆止口、领尖角歪咀、broken seam at collar point, slanted collar领贴不均、领圈不圆顺、fullness at collar placket, poor neck shaped, poor collar setting (not smooth).z.-装介英凸咀、底贴反吐、poor cuff setting (pointed out at
4、 seam), e*pose under layer at cuff装后中拉链起波浪衫身偏紧、拉链尾转角位起皱poor zipper setting on back body (wavy), too tight for wearing, puckering at zipper end领边捆条扭皱不均、neck piping twisted, torque on neck piping装腰头裤身位缩皱、裤头咀位上下、puckering under waist seam, hi-low waistband装腰头裾身位缩皱、裾头咀位上下、puckering under waist seam, hi-
5、low waistband左右侧骨长短+ -1/2 寸、uneven inseam / outseam length (+-) 1/2长有长短、uneven length on inseam车脚线阔窄、top stitches uneven width on bottom脚间线落坑、run off stitches on bottom脚间线阔窄、uneven top stitch at bottom长短脚、panel length uneven of bottom脚位凹凸不平、ugly hemming at bottom (at curve side)浪骨位皱、脚口不平直没烫好、puckeri
6、ng at rise seam, poor pressing at bottom (not leveling)脚叉长短、uneven bottom slit length前筒起皱、puckering on front placket脚围细 3/4 寸至 1 寸Bottom width -3/4 to -1腰围细 3/4waist is small by 3脚口不直顺hem uneven/bottom uneven上下脚、hem not leveled断线、broken stitches烫工不佳起镱痕烫过火pressing shine , (over pressing / hard pressi
7、ng).z.-布疵、色纱、走纱、破洞、fabric fault , color yarn, run off yarn, broken hole骨位间线驳线重线不佳、poor repairing stitches on double stitching面料有褶皱痕须烫好、crease line / folding line must improve by pressing腰驳幅位缩皱、puckering at waist panel seam腰缝起皱，wrinkles at waistband facing腰贴扭皱不平服，waistband is not laying smoothly with
8、 drag lines骨位间线扭皱没烫好、puckering on seam (poor pressing)上术问题请及时改善，否则会影响出货、Pls revise these problems /as above,or can shipout跳线、skipped stitches线头、thread end飞毛欠干净、fly yarn not cleanlinessskate spade进度表 progress chart.打褶、pleated sewing衫身起皱、winkle in body祥见尺寸表、see table size筒脚开、placket bottom spread open
9、驳线不良、bad joined stitches间线不良、improper top stitching筒边钮门位不顺直、button placket edge长短筒、uneven length of placket面布车得太贴拉链难拉、fabric too closed to zipper 、拉链起波浪、zipper wavy.z.-拉链谷皱、zipper crock领、collar 领面松，wrinkles at top collar 领面紧 top collar appears tight 领面起泡，crumples atop collar领不平衡平服unbalance collar领不对
10、称、asymmetric colla歪领、uneven collar上领凸咀、nose on collar setting烂领尖、burst collar point领窝起皱 two much ease on bogy after collar setting领面凹凸不平、tented collar领歪斜欠圆顺、poorly shaped ot round neck领罗纹起波浪、rid neck puckering左右领宽不一致、uneven roll左右领圈不一致、uneven collar point底领里起皱、wrinkles at collar band facing底领外露，coll
11、ar band lean out of collar左右前领咀形状不一样、uneren lipel shapes前领口常溶位太多、too much easing at c.f neckline领脚扭皱不平服、collar band is twisting后领中太紧、collar too tight at cb.z.-领及前领不平顺、fullness at front collar and lapel领装的不服帖不平顺、neckline is not smooth后领圈有上下、high & low back neckV 咀不正中、notch v off center前门领边不直、edgr of
12、front opening is crooked 或 front opening not straight前门领贴在下摆处外露、front facing e*posed at bottom hem前门领贴短于大身、front opening facing is shorter than body领圈拉松、neck was stretched突咀、e*cess e*tension袖和夹圈、sleeve &armhole下级领咀爆止口、collar stand end seam broken左右夹圈有溶位不平服、puckering at left/right armhole袖夹欠圆顺、poorly
13、 shaped of round armhole衣袖走后、sleeve running to back衣袖走前、sleeve running to front前袖骨拉松、too loose at front sleeve seam后袖骨过紧too tight back sleeve seam介英克夫装的不好 poor cuff setting /省尖起泡，crumples at dart point底缝骨拉松、underarm seam was stretched /小肩起皱，puckers at shoulders袖孔不顺、armhole setting not smooth /.z.-袖隆
14、起皱、creases at underarm袖顶缩拱不均有、ease on sleeve cap is uneven上袖打褶皱、pleated seam on sleeve前后幅片front / back谷钮筒、placket bubbling吊里、hiking at back lining too short前中拉链溶位太多、curve at cf zip (too much fullness at cf zip)前中拉链无溶位(引起拱起不平服)curve at cf zipper because of no easing of zipper拉链牙与边距太贴，导致拉链拉合困难tight cl
15、earance bctween the slider and the seam edge causing slider to operate with difficulty坏拉链 non functioned zipper漏拉链头、missing zipper puller拉链不能拉、zipper not movable后幅吊起、hiking at black /前幅吊起、hiking at front里布太大、lining too big里布太短、lining too short里布小、lining too small里布太长、lining too long前后幅布纹不对称、crain li
16、nes are not match at & back panel左右前长不一致、front length uneven袋 pocket.z.-上下袋唇不均、pocket welt is uneven左右袋子装得上下不一致、both pocket set uneven装袋不平服、不够方正、pocket not smooth/squared贴袋圆角位不圆顺、pocket corner not smooth and round上下袋、high-low pocket袋位左右上下、hi-low pocket袋盖不居中、pocket flap not centered oven pocket左右口袋形状
17、不一致、both pocket shapes art uneven袋口有毛口、pocket opening is fray /口袋变形、pocket shape distorted包边捆边binding断线、broken stitches跳线、skip stitches捆边扭曲不平顺、piping is twisting and not smooth捆边不均匀、piping is uneven缩褶、pleats后腰缩褶碎不均、uneven shriving at back waist seam克重、weight面料、抽纱 fabric draw yarn走纱、yarn run断线、broken
18、 stitches布疵、fabric defects.z.-色纱、color yarn粗纱、thick yarn抽纱、draw yarn破洞、broken hole断纱、broken yarn起泡、bubbling色差、color shading退色、color fading散口、raw edge污渍、dirt mark油渍 oil stain,粉渍、chalk mark 粉笔痕在钮位、chalk mark at button hole打枪痕、cleaning marks贴纸痕、sticker marks缝线外露、thread visible outside 前筒起蛇皱wavy atpacke
19、t杂色纤维织入、color fiber woven褶痕、crease mark 起皱、buckle面料褶皱痕未烫好、fabric puckering not leveling衫身有明显的折痕、visible pleated marks at body布料有死痕、permanent crease in the fabric成品外观有疵点、fabric flaws on outside garments.z.-长短袖、uneven length of sleeve /长短袖叉、uneven sleeve placket针步密度不均、uneven stitching density不均匀、uneve
20、n太细不平均、uneven size浪底十字骨错位、unmatched crotch cross钉珠、breading深浅色、uneven color扭脾、twist leg线头、uncut thread ends反光(止口反吐 、under ply turn out止口反骨、seam overturn车缝线落坑、run off stitches 前襟止口反吐、facing leans out from front edge毛粒、blub 、上装、 领子、collar 肩、shoulder 袖子、sleeve 袖口、cuff后背约克,开叉 Back yoke vent胸袋、侧袋、selvage
21、 pocket、side pocket拉链、隐形拉链、前身、侧缝、下摆。Zipper,invisible zipper,front part ,side seam,bottom省/Dart 褶/pleat 褶皱、wrinkle 起皱 creases marks下装裤腰、裤袢，waistband ,belt loop门襟，里襟，fly,under fly.z.-整烫极光，shining烫工不好引致缝骨起镱面、pressing too hard and mark seam shine整烫不良 poor pressing起皱严重须翻烫、e*cessive wrinkle that require p
22、ressing to over e蒸汽太多太少steam treating too much / too less烫痕 iron mark 熨烫过度 overpress熨烫不够 under press前褶位烫工不好、pressing on front pleat not well成品烫工差、poor pressing on garments/pressed poorly at garment烫工起镱面、shine caused by improper pressing烫痕，压痕 pressing mark乌绳结/扣 hook & eye不牢、insecured脾开骨没烫开骨 gamts not
23、 well pressed under thigh,should be open press seam颜色、 1/色差 color shade/color deviation线不配色、unmatched colour of thread颜色偏浅深color is too light/dark欠间线、missing top stitching褪色，color fading褪色问题 color fastness problem颜色组合错误 wrong bo图案错误、wrong pattern错码、wrong size indicated.z.-不正中、un centered辅助线外露、suppor
24、t stitches visible颜色完全不同、total different color(包装)装箱错误(数量，配比)或者缺少东西(拷贝纸，纸板)wrong packing for (quantity,collocation) missing tissue paper, cardboard唛头写错、wrong shippingmark logo受损唛头 、logo damaged边粗糙、logo raw edges错码 wrong size indicated唛头单词模糊、label illegible脏污严重必须处理 Must clean the spots(terrible)里襟里起皱
25、，creases at right fly双轨接线，stitch seam is uneven车脚、bottom hemming扭脚、twisted bottom脚口不齐平leg opening is uneven脚边不均/ uneven width of Bottom门筒脚位不直、placket sewing is curving at bottom门筒大小、uneven placket卷脚边扭皱不平直 wavy and twisting strolling hem脚边不平顺,侧骨脚口歪咀 bottom hem not smooth,side seam end not leveling at
26、 edge前后脚起蛇欠平直、not straight at front of body.z.-脚边有上下、up & down under of rib body衫脚欠平齐、up & down in bottom前筒弯曲、wavy placket前筒脚欠整齐、stepped at bottom of front placket车线跳针甩线车花Car yarn jump needle, take off the lineembroidery)脚位挑边跳针脱线、bottom skipped blinding stitches欠挑脚挑脚跳线bottom blinding stitch missing(
27、skip)挑脚线露牙、blinding stitch appeared at bottom hemming领 V 角位皱不平服 neck v angle wrinkle is not flatV 领边有缩皱现象、collar point not uniform袖夹位谷起欠顺/ wavy on the armhole夹圈露缝线/ visible linking in armhole袖夹爆缝/ holes on the armhole长短袖、uneven length of sleeve领边钉珠珠距欠均匀称 distance of every barding is not average尺寸欠稳定
28、/ measurement is not good尺寸偏细/ measurement in not insecure门筒大小/ uneven placket线头未剪不清uncut threads/thread not trimmed浮线/ cut threads loosing(loose threads)间线不均匀、stitching not uniform回针不牢、insecure back stitching.z.-左右袖长短、long & short between left & right sleeve袖口不直、the cuff is not straight喇叭口、flaring
29、out裤头驳线不佳、back stitching is found waistband上下裤头、high-low waistband裤头咀歪、distorted waistband end裤头凸咀、waistband end not close to front fly裤头间线不均、uneven edge stitching on waistband裤头扭皱、waistband twisted后中裤头位起皱、waistband near center back is puckering腰头位缩皱不均匀、puckering under waist seam,non-uniform尺寸欠稳定、me
30、asurement is not good尺寸偏细、measurement in insecure吊带长度短、uneven length of hanger钮门散口、raw edge on button hole钮不结实、stud insecure(easily to pull out)衫身条子欠顺直、not straight at rib body前襟长短、uneven length of front placket前襟吊里、shorter lining length on front facing(漏)打枣位置不对、bar-tack misplace /missing打枣位置不对、bar-
31、tack misplace打枣起褶、fold fabric by improper bar-tack sctting.z.-拉链不顺畅、zipper slider es off/siding not smooth拉链裂开、zipper split领尖贴布不均匀大小uneven V-inset锈花线不清、emb. unclean thread end主唛不正中、main label off center漏挂牌/价钱牌、missing hangtag / price ticket欠士啤钮、missing spare buttonV 领型不顺、V neck shape not smoothV 领不够
32、尖、Vneck point not shape enough领型不佳、slanted neck shape / not smooth领边打褶、pleat along neck ling前襟吊里、shorter lining length on front facing门筒位爆线、holes on the placketV 咀不正中、notch v off center里布有布疵、fabric defect on lining底爆止口 raw edge inside大货有 LOT 色明显、Big goods have a LOT of color is obvious面料走纱、fabric ya
33、rn run前幅条子不平服起皱、front blade not soothe wrinkle钮筒不直、front placket place ,position unsmooth脚贴兴里布位爆止口、seam broken on lining and hem facing袖骨欠间线、missing top stitch on sleeve seam.z.-骨位间线驳线重线不佳、poor repairing stitches on double stitching修改的衣服留有針孔痕跡、repair where the original seam stitching remains visible
34、前领口溶位太多有太多溶位于前领中领窝Too much easing at C.F neckline吊里 Hiking at back lining too short袖孔不圆顺 Armhole setting not smooth左右夹圈有溶位不平服 Puckering at left/right armhole右夹圈有拉松,左右夹圈不对称 Too loose at right armhole, uneven for left/right armhole介英装得不好 Poor cuff setting前中拉链溶位太多 Curve at CF zip (too much fullness at
35、CF zip)前中拉链无溶位(引起拱起不平服) Curve at CF zipper because of no easing of zipper后幅吊起/前幅吊起 Hiking at back/hiking at front里布太大，太短，太小，太长 Lining too big too short ；too small ；too long上下袋 High-low pocket左右口袋装得上下不一致 Both pocket set uneven袋不平服、不够方正 Pocket not smooth/squared袋盖不居中 Pocket flap not centered over pock
36、et左右口袋形状不一致 Both pocket shapes are uneven口袋下部下垂 Bottom part of pocket is sagging袋边位置不对 Pocket flap is misplaced袋口开得不吻合 Pocket is smiling袋口有毛口 Pocket opening is fray口袋变形 Pocket shape distorted.z.-拉捆包边 binding捆边扭曲不平顺 Piping is twisting and not smooth捆边不均匀 Piping is uneven后腰缩碎褶不均匀 Uneven shriving at back waist seam.z.
