《品保常用英语.doc》由会员分享，可在线阅读，更多相关《品保常用英语.doc（7页珍藏版）》请在金锄头文库上搜索。
1、一. 產品1. Memory Socket: 記憶體插槽 DIMM: Dual In Line Memory Module Socket 雙向記憶體擴充槽 結構: Housing 塑膠 Contact 端子-carrier 沿邊料+Bellow + tail + V-cut M.H.D. : Metal Hold Down 金屬卡勾 Ejector2. H/D: Header結構: housing, contact, four wall, key, mating, stand off, tail, kink, pin, post3. F/C: Flat Cable扁平排線結構: IDC: In
2、sulation Displacing Connector 絕緣刺破連接器 Cover, S/R (Strain Relief), Cable二. 制程1. Stranding wire: 絞線2. Cable extrusion: 線纜押出3. Stamping: 沖壓-Stretching wire 抽線4. Plating: 電鍍5. Molding: 成型-cavity, die /mold, core pin (公模,模仁), cavity pin (母模)6. Assembly: 裝配三. 檢測與設備1. open-short test: 導通測試2. Hi-pot: 耐高壓測試3
3、. Projector: 投影機4. callipers: 卡尺5. microscope: 顯微鏡6. multimeter: 萬用電表7. oven: 高溫爐8. salt spray tester: 鹽水噴霧機9. voltage resistant : 耐電壓測試10. elongation test: 伸長率測試11. steam aging: 蒸氣老化試驗12. weight: 砝碼13. balance: 天平四. Terms:Check檢查Inspect檢驗Sampling抽樣dimension (DIM)尺寸tolerance公差true position真位度revisio
4、n (Rev.)版次quantity(Qty)數量quality質量work in process在制品specification (Spec.)規格normal正常tightened加嚴reduced減量critical defect (CRI.)嚴重缺點major defect (MAJ.)主要缺點minor defect (MIN.)次要缺點accept允收reject拒收waive特采scrap報廢rework重工sort挑選scale比例location位置reference (REF.)參考marking標記Appearance Inspection外觀檢驗Lead time (L
5、/T)前置時間Line down斷線Warehouse倉庫Inventory庫存Pallet棧板Carton紙箱Packing包裝Gold 金Nickel鎳Tin錫Lead鉛五. 縮寫1. B/M: Board Mount2. PBG: Products Business Group3. 3C: Computer, Communication, Consumer4. ZD: Zero Defect5. VP: Vice President6. MGR: Manager7. QC: Quality Control8. QA: Quality Assurance9. TQC: Total Qual
6、ity Control10. TQA: Total Quality Assurance11. IPQA: In Process Quality Audit12. IPQC: In Process Quality Control13. FQC: Final Quality Control14. OBA: Out of Box Audit15. IQC: Incoming Quality Control16. OQC: Outgoing Quality Control17. QE: Quality Engineer18. PQE: Process Quality Engineer19. FAE:
7、Field Application Engineer20. PM: Product Market21. C/N: Customer Number22. P/N: Part Number23. SOP: Standard Operation Procedure24. PMP: Product Management Plan25. ECN: Engineering Change Notice26. VDCS: Vendor Defects Correction Sheet27. SWR: Special Work Request28. FAR: Failure Analysis Report 29
8、. CAR: Corrective Action Report30. CCTF: Customer Complaint Track Form31. CSTF: Customer Service Track Form32. FMEA: Failure Mode & Effect Analysis33. QAN: Quality Alarm Notice34. AVL: Approved Vendor List35. BOM: Bill of Material36. WDR: Weekly Delivery Requirement37. TIP: Tip Innovation Plan38. QC
9、C: Quality Control Circle39. QIT: Quality Improvement Team40. 5W1H: When, Where, Who, What, Why, How41. 5M: Man, Machine, Material, Method, Measurement42. FAI: First Article Inspection43. AQL: Accept Quality Level44. SPC: Statistical Process Control45. LRR: Lot Reject Rate46. DPM: Defect Per Million
10、47. PPM: Parts Per Million48. GRR: Gauge Repeatability and Reproducibility49. ISO: International Standard Organization50. UL: Underwriters Laboratories Inc. 美國保險協會51. CSA: Canadian Standards Association 加拿大標準協會52. ANSI: American National Standard Institute 美國標准協會53. QMC: Quick Measurement Center54.
11、MRB: Material Review Board55. IE: Industry Engineering56. ME: Mechanical Engineering57. FYI: For Your Information58. TBA: To Be assigned59. ETD: Estimated Time Of Delivery60. ETA: Estimated Time Of Arrival61. PCB: Printed Circuit Board62. SMT: Surface Mount Technology63. PC: Personal Computer64. HDD
12、: Hard Disk Drive65. FDD: Floppy Disk Drive66. CPU: Central Processing Unit67. CD: Compact Disk68.CD-ROM: Compact Disk Read Only Memory六. 藍圖英語1. DIMM (take 318-0000-075 as an example)Notes: Unless otherwise specified1) Interpret drawings per ANSI Y14.5M-19822) Dimensions marked to be checked by QC.D
13、imensions marked to be checked by process control and QC.3) Solder tail true positions should be checked using PCB gage No. 850-0841-4914) Ejectors should be securely mounted onto the housing.5) The top section of the contacts should touch the housing preload stopper.6) Retention force: 0.34kg min per contact.7) The lot identification code is marking by laser coding and the location is approximately as shown with a height 1.2mm. This lot identification code is specified as follows: Week / The last two d
