《华为交换机.思科交换机限制带宽.doc》由会员分享，可在线阅读，更多相关《华为交换机.思科交换机限制带宽.doc（6页珍藏版）》请在金锄头文库上搜索。
1、交换机命令：华为交换机：sys /进入系统LinkIDC-LF-J5di cu /系统LinkIDC-LF-J5int e1/0/2 /进入端口LinkIDC-LF-J5-Ethernet1/0/2int e1/0/3 /更换成3端口LinkIDC-LF-J5-Ethernet1/0/3line i 5120 /进的带宽为 5120KLinkIDC-LF-J5-Ethernet1/0/3line o 5120 /出的带宽为 5120KLinkIDC-LF-J5-Ethernet1/0/3q /quit 退出LinkIDC-LF-J5q /quit退出sa /save 保存，如不保存，重启交换机
2、后，将恢复原始设置注意：本命令使用了短命令，如果想查看全命令，请使用 tab键补全命令。-思科交换机：enable /进入特权模式s1#show run /显示系统配置s1#conf t /进入配置终端模式s1-config? /可以通过打问号提示所要找的命令Switch#conf t /进入配置模式Switch(config)#interface fastEthernet 0/22 /进入端口Switch(config-if)#storm-control unicast level 2 /限制单播风暴为 2%，如果100Mb带宽则为2MbSwitch(config-if)#exit /退出端
3、口管理Switch(config)#exit /退出配置模式Switch#write /保存-思科交换机实例操作：PCtelnet 10.0.0.60Trying 10.0.0.60 .OpenUser Access VerificationPassword: SwitchenPassword: Switch#sh ruBuilding configuration.Current configuration : 1157 bytes!version 12.1no service timestamps log datetime msecno service timestamps debug da
4、tetime msecno service password-encryption!hostname Switch!enable password 123321!interface FastEthernet0/1 storm-control broadcast level 1!interface FastEthernet0/2 storm-control broadcast level 1!interface FastEthernet0/3!interface FastEthernet0/4!interface FastEthernet0/5!interface FastEthernet0/6
5、!interface FastEthernet0/7!interface FastEthernet0/8!interface FastEthernet0/9!interface FastEthernet0/10!interface FastEthernet0/11!interface FastEthernet0/12!interface FastEthernet0/13!interface FastEthernet0/14!interface FastEthernet0/15!interface FastEthernet0/16!interface FastEthernet0/17!inter
6、face FastEthernet0/18!interface FastEthernet0/19!interface FastEthernet0/20!interface FastEthernet0/21!interface FastEthernet0/22!interface FastEthernet0/23!interface FastEthernet0/24!interface GigabitEthernet1/1!interface GigabitEthernet1/2!interface Vlan1 ip address 10.0.0.60 255.255.0.0!ip defaul
7、t-gateway 10.0.0.60!line con 0!line vty 0 4 password 123321 loginline vty 5 15 login!endSwitch#conf tEnter configuration commands, one per line. End with CNTL/Z.Switch(config)#interSwitch(config)#interface faSwitch(config)#interface fastEthernet0/1Switch(config-if)#stoSwitch(config-if)#storm-control unicast level 2Switch(config-if)#exitSwitch(config)#exitSwitch#writeBuilding configuration.OKSwitch#
