《小型客车制动力分配比分析与优化》由会员分享，可在线阅读，更多相关《小型客车制动力分配比分析与优化（60页珍藏版）》请在金锄头文库上搜索。
1、华北科技学院 摘 要 以常规能源为基础的能源结构随着资源的不断的消耗，将越来越不适应可持续能源的发展的需要。加速开发以太阳能为主体的可再生能源以成为人们的共识。太阳能作为一种作为一种清洁能源，倍受人们重视。精确跟踪太阳，对太阳能利用率的提高是显著的，市场上急需一种高精度，高稳定性的跟踪控制器。 跟踪太阳的方式主要有光电跟踪和视日运动轨迹跟踪。光电跟踪主要控制过程是：由光敏传感器采集太阳与光伏电池板之间水平与垂直方向的位置偏差信号与光强信号，并反馈给数据处理器与控制器，经过数据的处理与放大，发出驱动信号，经过驱动电路控制步进电机的转动，经过减速机构缓慢调整角度。视日运动轨迹跟踪将太阳位置受时间、
2、季节、所在地区经维度等因素综合考虑。 本设计采用光时互补的跟踪方法，即是以视日运动轨迹跟踪为粗调，从时钟模块读出当前时间计算出太阳的空间位置，并根据经纬度进一步计算出太阳的方位角和高度角。由单片机发出驱动信号控制步进电机转动，到达指定位置。先大致定位太阳的位置。当转到既定位置之后再采用光电跟踪方式，精确定位。这样可以互相弥补不足。为完成本设计，本文对跟踪方式进行了深入的研究，并在此基础上主要采用CDS光敏电阻，STC12C5A单片机与步进电机完成跟踪器的设计。首先根据设计要求和指标，提出系统的设计方案并确定方案性原理上的可行性。根据要求和各个模块的功能，完成主要器件的选型。在硬件系统设计的基础
3、上，使用汇编语言完成软件程序的程序编写。最后，论文还对整个课题设计进行总结，并对课题中存在的问题提出了改善措施和进一步完善本系统的建议。主要工作包括以下内容： （1）设计太阳能电池板自动跟踪的电路原理图; （2）设计单片机的外围电路，光电转换电路，步进电机驱动控制电路; （3）设计整个系统的电路原理图; （4）软件的设计：使用C51语言实现了单片机的控制程序设计; 关键词： 光电跟踪;视日运动轨迹跟踪;光敏电阻;单片机AbstractAs the consumption of natural resources based on conventional energy sources in e
4、nergy structure, it will not become more and more able to meet the requirements for sustainable energy development. It becomes our common views to accelerate the exploitation of the solar energy which is the the main body of the renewable energy. As a kind of clean energy, the solar energy is becomi
5、ng much appreciated. Therefore, tracking the sun precisely is significant to improve the utilization rate of solar energy and the market need a high-precision, high stability tracking controller.There are mainly two ways to track the sun , including tracking the sun by photosensitive sensor and trac
6、king the suns trajectory. The process of tracking by sensor is mainly : the sensor receive the signals which are the position discrepancy between the sunlight and the solar panel，in other word ,that is the position of the horizontal and vertical direction deviation. And feedback to the data processo
7、r and controller, then process the data and amplify , output driving signal . At last ,through the rotation of the stepper motor controlled by driving circuit and reduction box , it just adjust the angle until the sunray is completely perpendicular to the solar panel. The sun trajectory tracking mod
8、e is made ,given some other comprehensive factors such as time, season ,latitude and longitude . This design use both tracking methods which are complementary . In other words ,it depends on the trajectory tracking for coarse adjustment ,which locate the sun. When it rotate on the setting position ,
9、it will activate the photosensitive sensor to adjust the panels position accurately. And it can offset the both imperfections . To complete this design, this paper makes a deep research . And on this basis, we mainly use the Photosensitive resistance-CDS ,STC12C5A and stepping motor to complete the
10、design of the tracker.First of all, according to the design requirements, we put forward system design plan and determine the feasibility of the project in principle. According to the requirements and function of each module, we complete the selection of main device. On the basis of the hardware sys
11、tem,use the assembly language to complete this programming. Finally, the paper summarizes the whole project design, and puts forward improvement measures on the problems existing in the subject and suggestions to improve. Main work includes the following contents:(1) Design Automatic tracking solar
12、panel of the circuit diagram;(2) Design the MCU peripheral circuit , photoelectric conversion circuit, stepper motor drive control circuit; (3) Design circuit diagram of the entire system; (4) The design of the software: use C51 language to realize the control program design by single chip microcomp
13、uter ;Key words: sun tracking of using photosensitive sensor ; suns trajectory tracking ; Photosensitive resistance; Single chip microcomputer目录摘 要IAbstractII第1章 绪论11.1 太阳能电池板自动跟踪系统设计的背景及意义11.2 太阳光自动跟踪系统的国内外研究现状21.3 项目研究的主要内容及预期目标5第2章 太阳能电池板跟踪相关理论研究62.1 太阳的运行规律62.1.1 太阳高度角，方位角及时角介绍62.1.2 太阳高度角及方位角计算
14、公式62.1.3 太阳能电池板跟踪参考坐标系82.2 光伏电池的特性分析92.2.1 光伏电池的光伏效应92.2.2 温度对光伏电池输出特性的影响92.2.3 太阳的光照强度对光伏电池转换效率的影响102.2.4 光伏电池的I-V和P-V特性曲线11第3章 太阳能跟踪系统的控制目标与控制方案123.1 控制方案选择123.2 控制方案设计133.2.1 光敏电阻设计的传感器133.2.2 跟踪控制系统整体原理框图143.2.3 太阳能自动跟踪装置设计15第4章 电池板跟踪系统硬件设计164.1 关键器件介绍164.1.1 STC12C5A60S2简介164.1.2 步进电机介绍184.1.3
15、光敏传感器及元件204.2 CPU模块设计214.2.1 CPU硬件模块结构框图214.2.2 CPU 模块电路原理图224.2.3 复位电路234.2.4 晶振电路234.2.5 发光二极管244.3 光电传感模块244.4 实时时钟模块274.5 RS232通讯模块284.6 EEPROM存储模块294.7 系统电源设计304.8 步进电机驱动电路30第5章 太阳能电池板跟踪系统软件设计315.1 Keil C51 软件介绍315.2 软件总体设计及流程图325.2.1 软件总体设计325.2.2 软件流程图设计335.3 软件关键模块设计345.3.1 串口通信程序设计345.3.2 EEPROM的读写程序核心代码345.4 程序设计要点及注意事项36第6章 实验及结论40第7章 总结及展望417.1 总结417.2 展望41第8章 附录428.1 控制板原理图428.2 部分数据结构428.3 部分软件代码46参 考 文 献53致谢54
