京东方液晶检测标准iis

上传人:简****9 文档编号:99541743 上传时间:2019-09-19 格式:PDF 页数:10 大小:258.73KB
返回 下载 相关 举报
京东方液晶检测标准iis_第1页
第1页 / 共10页
京东方液晶检测标准iis_第2页
第2页 / 共10页
京东方液晶检测标准iis_第3页
第3页 / 共10页
京东方液晶检测标准iis_第4页
第4页 / 共10页
京东方液晶检测标准iis_第5页
第5页 / 共10页
点击查看更多>>
资源描述

《京东方液晶检测标准iis》由会员分享,可在线阅读,更多相关《京东方液晶检测标准iis(10页珍藏版)》请在金锄头文库上搜索。

1、PROPRIETARY NOTE - 15“ XGA, P-Grade SPEC. NUMBERPRODUCT GROUP ISSUE DATE PAGE B2006-5006-O (1/3)A4(210 X 297) 2006-8-3S844-5015TFT-LCD PRODUCTO THIS SPECIFICATION IS THE PROPERTY OF BOEOT AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOEOT AND MUST BE RETURNED TO BOEOT UPON

2、 ITS REQUEST. REV. TITLEVISUAL INSPECTION CRITERIA FOR ALL CUSTOMERS : 1 OF 10 BEIJING BOE OPTOELECTRONICS THCHNOLOGY PROUCT GROUPREV.ISSUE DATE TFT PRODUCTSO ContentsContents Revision History 3 1.0Introduction 1.1.Scope 4 1.2. Incoming Inspection Right . 4 1.3.Handling Precautions . 4 2.1.Sampling

3、Method 5 2.2.Inspection Method 5 2.3.Definitions . 5 3.0Inspection Criteria 3.1. Visual Inspection Criteria . 7 3.2.Apperarence Inspection Criteria 8 4.0RMAs 4.1. Verification 9 4.2.Supplier Induced Defects 9 4.3.Customer Induced Defects 9 4.4. RMA Shipment LCMs shipment 9 5.0 Warranty 5.1.Warranty

4、Period 10 5.2.Repair Warranty 10 5.3.Warranty avoidance 10 6.0 Others 10 SPEC. NUMBER SPEC. TITLE PAGE VISUAL INSPECTION CRITERIA FOR CUSTOMER2 OF 10 (15.0“ XGA-P) B2006-5006-O (1/3)A4(210 X 297) 2006-8-03 S844-5015 2.0Generals PROUCT GROUPREV.ISSUE DATE TFT PRODUCTSO REVISION HISTORY REV.ECN NO. DE

5、SCRIPTION OF CHANGESDATEPREPARED OINITIAL RELEASE SPEC. NUMBER SPEC. TITLE PAGE VISUAL INSPECTION CRITERIA FOR CUSTOMER3 OF 10 (15.0“ XGA-P) B2006-5006-O (2/3)A4(210 X 297) 2006-8-03 S844-5015 -XUWEI2006-8-3 PROUCT GROUPREV.ISSUE DATE TFT PRODUCTS2006-8-03 1.0 IntroductionIntroduction 1.1.Scope call

6、 the LCMs supplied by BOEOT hereafter called the Supplierto its Customer “) ( “) . The Customer shall have the right to conduct at its own cost and expense an incoming , inspection of the LCMs at the destination specified in the relevant B L Bills of Lading in / ( ) criteria set forth in this articl

7、e . The customer shall notify the Supplier in writing of the inspection results acceptance ( or rejectance in accordance with the said Incoming Inspection Standard within ) 40 days from the date of the B L / . Should the Customer fail to notify the results to Supplier with 40days period the right to

8、 , reject the LCMs shall then lapse and the said LCMs shall be deemed to have been , accepted by the Customer . 1.3.Handling Precautions broken or cracked if dropped it So PLEASE handle them with care . . DO NOT press the area covered with PET or such materials These are weak -. . point of LCMs sinc

9、e of TCPs Driver ICs and PWBs ( ) . PLEASE support the Bezel with your finger when connecting the interface cable -. . Semiconductive devices are included in the LCMs and they should be handled with care to prevent any electrostatic discharge ESD (). DO NOT stack the LCMs too high without wrapping m

10、aterial such as AIR CAP -. . Before use the LCMs PLEASE check the Engineering specification -. , . LCMs contain a small amount of Liquid Crystal and Mercury PLEASE follow local -. . ordinances or regulations for disposal . SPEC. NUMBER SPEC. TITLE PAGE VISUAL INSPECTION CRITERIA FOR CUSTOMER4 OF 10

11、(15.0“ XGA-P) B2006-5006-O (3/3)A4(210 X 297) S844-5015 This incoming Inspection Standard shall be applied to TFT LCD modules hereafter - ( LCM Devices are made of fragile material such as Glass and plastic and may be -. 1.2.Incoming inspection Right O accordance with the LCMs specifications separat

12、ely agreed upon and the inspection PLEASE wear the Wrist Strap when handling -. . PLEASE DO NOT touch the surface of the Glass Polarizer -. (). PLEASE keep the LCMs in the specified original packing boxes when storage -. , . PROUCT GROUPREV.ISSUE DATE TFT PRODUCTS2006-8-03 2.0 GeneralsGenerals 2.1.S

13、ampling Method Unless otherwise agreed upon in writing the sampling inspection shall be applied to , the Customers incoming inspection . 2.1.1. Lot size :1pallet per same model 2.1.2.Sampling typeRandom sampling : 2.1.3. Inspection levelII : 2.1.4.Sampling tableMIL STD : -105E 2.2.Inspection Environment 30CM50CM 2.2.1.Ambient conditions bRelative Humidity . : 65 20%RH cAmbient Illumination . : 300700 LUX Normal (:500LUX) 2.2.2.Vi

展开阅读全文
相关资源
正为您匹配相似的精品文档
相关搜索

最新文档


当前位置:首页 > 商业/管理/HR > 管理学资料

电脑版 |金锄头文库版权所有
经营许可证:蜀ICP备13022795号 | 川公网安备 51140202000112号