《ams 5659p 耐蚀合金棒材、丝材、锻件、环材和型材15-5ph自耗电极熔炼,固溶热处理,可沉淀硬化》由会员分享，可在线阅读，更多相关《ams 5659p 耐蚀合金棒材、丝材、锻件、环材和型材15-5ph自耗电极熔炼,固溶热处理,可沉淀硬化（9页珍藏版）》请在金锄头文库上搜索。
1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2013 SAE International All rights reserved. No part of this p
3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER:Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970
4、 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS:http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5659P AEROSPACE MATERIAL SPECIFICATION AMS5659REV. P Issued1965-09 Revised2014-0
5、2 Superseding AMS5659N Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 15Cr - 4.5Ni - 0.30Cb (Nb) - 3.5Cu (Composition similar to UNS S15500) RATIONALE AMS5659P results from a limited scope ballot to revise Heat Treatment (3.4), Classification of Tests (4.2) and Reports (4.4)
6、. 1.SCOPE 1.1Form This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, flash welded rings, and extrusions in the solution heat treated condition (See 8.3), and stock for forging, flash welded rings, or extruding. 1.1.1For purchase of solution treated and aged pr
7、oduct, use the applicable AMS slash specification (See 8.3). If a slash sheet description is not specified, solution annealed material shall be supplied. A specific example of a slash specification is: AMS5659/H1025 Precipitation Hardened to H1025 condition 1.2Application These products have been us
8、ed typically for parts requiring corrosion resistance and high strength up to 600 F (316 C) with good ductility and strength in the transverse direction in large section sizes, but usage is not limited to such applications. 1.2.1Certain design and processing procedures may cause these products to be
9、come susceptible to stress-corrosion cracking; ARP1110 recommends practices to minimize such conditions. 1.3Classification Products covered by this specification are classified as follows: Type 1 -Steel multiple melted using vacuum consumable electrode remelting. Type 2 -Steel multiple melted using
10、electroslag remelting. 1.3.1Unless a specific type is ordered, either type may be supplied. SAE InternationalLicensee=COMAC, Shanghai Aviation Industry(Group) Co Ltd 5973222 Not for Resale, 2014/8/13 03:30:06 No reproduction or networking permitted without license from IHS -,-,- SAE INTERNATIONALAMS
11、5659PPage 2 of 9 2.APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When
12、 the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724
13、-776-4970 (outside USA), www.sae.org. AMS2241Tolerances, Corrosion and Heat-Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Bars and Wire AMS2248Chemical Check Analysis Limits, Corrosion and Heat-Resistant Steels and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron Alloys AMS2300
14、Steel Cleanliness, Premium Aircraft-Quality, Magnetic Particle Inspection Procedure AMS2315Determination of Delta Ferrite Content AMS2371Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging Stock AMS2374Quality Assurance Sampling and Te
15、sting, Corrosion and Heat-Resistant Steel and Alloy Forgings AMS2750Pyrometry AMS2806Identification, Bars, Wire, Mechanical Tubing, and Extrusions, Carbon and Alloy Steels and Corrosion and Heat-Resistant Steels and Alloys AMS2808Identification, Forgings AMS5659/H1025Steel, Corrosion-Resistant, Bars
16、, Wire, Forgings, Rings, and Extrusions, 15Cr 4.5Ni 0.30Cb (Nb) 3.5Cu, Consumable Remelted, Solution and Precipitation Heat Treated (H1025) AMS7490Rings, Flash Welded, Corrosion and Heat-Resistant Austenitic Steels, Austenitic-Type Iron, Nickel, or Cobalt Alloys, or Precipitation-Hardenable Alloys AMS-H-
