《en60335-2-9a13和ek1的解释》由会员分享，可在线阅读，更多相关《en60335-2-9a13和ek1的解释（21页珍藏版）》请在金锄头文库上搜索。
1、部门： 研究院测试认证中心 时间：2011年07月30日,EN60335-2-9:A13:2010+EK1 解释,微波电器事业部,EN60335-2-9/A13:2010,1) EN 60335-2-9/A13:2010 Part 2-9: Particular requirements for grills, toasters and similar portable cooking appliance,发布期 DOP: 2011-10-01 强制实施期 DOW: 2013-10-01,2) EK1AG2 （以下简称EK1) Guidance for Implementation of CE
2、NELEC Guide 29 Test and Certification Decisions,发布期 DOP: 2011-07-01 强制实施期 DOW: 2011-10-01 凡需要获得GS证书必须满足EK1的要求！,EN60335-2-9/A13:2010,涉及小于18Kg的桌面微波炉，带烧烤功能,一、结构更改 1）后背电源线插孔： 原因：,8.1.1 Test probe B and probe 18 of EN 61032 are applied without appreciable force, the appliance being in every possible posi
3、tion except that appliances normally used on the floor and having a mass exceeding 40 kg are not tilted. Through openings, the test probe is applied to any depth that the probe will permit and is rotated or angled before, during and after insertion to any position. If the opening does not allow the
4、entry of the probe, the force on the probe in the straight position is increased to 20 N when probe B is used or 10 N when probe 18 is used. If the probe then enters the opening, the test is repeated with the probe in the angled position. However when using test probe 18 the appliance shall be fully
5、 assembled as in normal operation without any parts removed; parts that are intended to be removed for user maintenance shall not be removed.使用测试指18的时候,期间在正常操作情况下测试. 任何可拆卸部件都不拆卸,EN60335-2-9/A13:2010,防危险运动部分的新的测试方法: 20.2Replace the first paragraph of compliance by: Compliance is checked by inspection
6、, by the tests of 21.1 and by means of: a test probe that is similar to test probe B of IEC 61032 but having a circular stop face with a diameter of 50 mm, instead of the non circular face, applied with a force of 5 N and test probe 18 of IEC 61032, applied with a force of 2,5 N.,Probe 18,Department
7、 name,18 January 2019,EN60335-2-9/A13:2010,EN60335-2-9/A13:2010,孔径为10mm，Probe 18的可以插进去， 碰到运动的扇叶或高压电容的带电部分,EN60335-2-9/A13:2010,一、结构更改 2）门玻璃、顶部，左侧，右侧，后背： 原因：,11.Z101 Ovens, rotary grills, rotisseries and cookers are supplied at rated power and operated under normal operation. All heating units that c
8、an be connected to the supply mains at the same time during normal use are switched on. Ovens are operated without accessories. 测试方法：额定功率测试烧烤温升, Ovens are operated with the door closed. Ovens having a thermostat are adjusted to its high setting. 温升考核点：所有可以被Probe41,ProbeA(EK1)接触的表面 Temperature rises
9、are not measured on the following surfaces,EN60335-2-9/A13:2010,1) surfaces on the oven door within 10 mm from the edge of the door (Zone 1); 2) surfaces around the oven door within 10 mm from the left right or lower edge of the door, or25 mm from the upper edge of the door (Zone 2); 3) surfaces wit
10、hin 25 mm of vents (Zone 3); EK1仅豁免：Only the ventilation openings on the front side are exempted from the evaluation (ventilation of the muffle, zone 3(refer to picture Z102). 其他：The temperature rise around all other ventilation openings has to comply with the requirements of touchable surfaces (tab
11、le Z.101). 4） underside surfaces that are not accessible with test probe 41, probe A(EK1) of EN 61032， 5) the rear surface of appliances which, according to the instructions, shall be placed against a wall; and are not accessible with test probe 41,probe A(EK1) of EN 61032，,EN60335-2-9/A13:2010,EN60
12、335-2-9/A13:2010,Probe 41:,EN60335-2-9/A13:2010,Probe A:,EN60335-2-9/A13:2010,限值的对比:,请注意Note b!,EN60335-2-9/A13:2010,25mm豁免,10mm豁免,10mm豁免,Bare metal: 45K,Plastic: 65K,Glass: 60K,Bare metal: 45K (EK1:无通风口25mm豁免说法),EN60335-2-9/A13:2010,10mm豁免,10mm豁免,25mm豁免,Coated metal 55K,Coated metal 55K,判断为Coated m
13、etal前提是： Metal is considered coated when a coating having a minimum Thickness of 80um made by enamel or non substantially Plastic coating is used.,EN60335-2-9/A13:2010,10mm豁免,10mm豁免,25mm豁免,Coated metal 55K,Coated metal 55K,判断为Coated metal前提是： Metal is considered coated when a coating having a minimu
14、m Thickness of 80um made by enamel or non substantially Plastic coating is used.,EN60335-2-9/A13:2010,Coated metal 55K Bare metal 45K,在说明书有“the rear surface of appliances shall be placed against a wall”下,炉子底板部位， 若碰到则为 Coated metal 55K Bare metal 45K,EK1:,判断为Coated metal前提是： Metal is considered coate
15、d when a coating having a minimum Thickness of 80um made by enamel or non substantially Plastic coating is used.,EN60335-2-9/A13:2010,一、结构更改 3）器具的start/stop开关需要给用户提供视觉和听觉或者触觉的反馈： 原因：,7.10 Addition: Devices used to start/stop operational functions of the appliance, if any, shall be distinguished from
16、 other manual devices by means of shape, or size, or surface texture, or position, etc. A tactile or an audible and visual feedback shall give an indication that the device has been operated.,EN60335-2-9/A13:2010,机械式不满足要求， 定时器形状必须与调节开关不一样， 必须有叮的声音,电子式不满足要求， Start/off的形状、 按键声音能否 与其他按键不一样？,正常工作的时候灯亮,EN60335-2-9/A13:2010,二、说明书,增加：,增加： the rear surface of appliances shall be placed against a wall,EN60335-2-9/A13:2010,注意：,EN60335-2-9/A13:2010,END,
