《Motioncontrol液压回转控制》由会员分享，可在线阅读，更多相关《Motioncontrol液压回转控制（3页珍藏版）》请在金锄头文库上搜索。
1、Bosch Rexroth Oil Control S.p.A.MOTION CONTROL4d) MOTION CONTROLBosch Rexroth Oil Control manufactures a variety of valves for pressure, flow and motion control of actuators working in both forward and reverse direction. A few of these valves are designed to be line mounted on the 2 main hoses, but
2、many of them are studied to match the port patterns of commercially available hydraulic motors and they can be flanged onto the motor directly simplifying plumbing and saving space. This catalogue shows examples of valves for Rexroth A2FE Series and Sauer-Danfoss orbital motors, but the valve range
3、extends to a number of other motors as well. The valves are grouped by hydraulic function as follows: 4a) DUAL CROSS OVER RELIEF 4b) SINGLE COUNTERBALANCE WITH BRAKE RELEASE PORT 4c) DUAL COUNTERBALANCE WITH BRAKE RELEASE PORT 4d) MOTION CONTROLThis family of valves performs the following main funct
4、ions:A Free flow into the motor through the check valves from both the main supply lines.B Limitation of the inlet pressure through the cross-over type relief valves which transfer the exhausted oil to the other line (from V1 to V2 and vice-versa).C Locking of the motor by locking the reverse flow a
5、t both the motor ports, when the directional valve is in central position, or the pump is stopped.D Bi-directional control of the motion always metered by the pilot function: the pilot pistons modulate the openings of the relief valves which become counterbalance valves, and control the speed by met
6、ering the oil flow discharged from the motor. Motion is possible only in presence of pilot pressure, i.e. positive inlet pressure to the motor, also when the load tends to overrun.E Limitation of back-pressure at the motor exhaust ports especially during braking. The cross-over relief valves limit t
7、he braking pressure and transfer the exhausted oil to the other line in order to re-fill the motor and to prevent cavitation also during braking when no pump flow is delivered to either one of the motor ports.Bosch Rexroth Oil Control S.p.A.where: Pt = pressure setting (relief setting) Pload = load
8、induced pressure R = pilot ratioExample: Pload max = 170 bar (maximum expected load induced pressure) Pt = 325 bar ( 1.3 x 170 bar ) R = 8:1 (Pilot ratio) Brake release pressure: 17 bar (Ppil min) =325 - 1708 + 1bar = 17.2 bar 17 barF Additional functions in “VF” and “PDRM” versions(see schemes):“VF
9、” version: it allows direct control of the mechanical parking brake, with the pressure delivered by a shuttle valve through “C3” port. If it is necessary to limit the pressure to the brake, a pressure reducer cartridge may be incorporated into the valve between the shuttle and C3.For motion control
10、of hydraulic motors, generally a high pilot ratio “R” is adopted in order to speed up motion and save energy; however, if the valve selected is a “VF” version, it must always be remembered that “R” must comply with the following limitations: the “pilot pressure” needed to open the relief cartridge a
11、nd start motion must always be “higher” than the pressure capable to release the brake (generally 7 to 1520 bar). In fact, when motion is commanded in either direction, the pilot pressure must build-up to a level capable to release the brake before any motion starts. With hydraulic motors, the pilot
12、 pressure needed to open the counterbalance valve can be calculated by the following formula:“VF” versionPpil =Pt - PloadR + 1and the lowest pilot pressure (Ppil) is:(Ppil min) =Pt - Pload maxR + 1The selected motion control valve, with R = 8 : 1 and Pt = 325 bar, complies with the correct lowering
13、sequence because the lowest pilot pressure is 17.2 bar 17 bar: also with the highest load capacity, the holding brake is released before any motion of the hydraulic motor is started. If compliance is not met, a different pilot ratio or a different pressure setting must be selected.NOTE: for proper c
14、ontrol of the parking brake, it is often necessary to add devices designed to delay the brake engagement after bringing the control spool in central position, until the motion has reached a definite full stop, without delaying the brake release at start (see scheme).Bosch Rexroth Oil Control S.p.A.“
15、PDRM” version: it has relief cartridges with two different pressure settings, both separately adjustable:a) high pressure setting for starting (oil flow from V1 to C1, or V2 to C2 ).b) low pressure setting for smooth braking during stopping (oil flow from C1 or C2), when the directional control valv
16、e is brought into the central position.High and low settings can be achieved because each relief piston is pushed by two springs, a main spring and a secondary spring, acting in opposite directions. When oil is flowing from V1 to C1 (or V2 to C2), the secondary spring is neutralized by the incoming flow and the relief piston is controlled only by the main spring: the line pressure is at its highest va
