《官方说明书hacker X-Pro Speedcontroller》由会员分享，可在线阅读，更多相关《官方说明书hacker X-Pro Speedcontroller（7页珍藏版）》请在金锄头文库上搜索。
1、hacker X-Pro Speedcontroller http:/ ManualLManualL collects and classifies the global product instrunction manuals to help users access anytime and anywhere, helping users make better use of products.Home: http:/ Chinese: http:/ Manual: http:/ X-Pro SpeedcontrollerSpeedcontroller Dear Customer, Than
2、k you for your purchase of the X- Series Controller, a new generation of sensorless speed controllers especially for Hacker Brushless A-Series- Motors and other Brushless Motor Designs. Special programming options are provided to ensure the best possible power and performance from your motor system.
3、 Brushless systems offer high power efficiency combined with low weight and compact dimensions. For best performance and reliability from your Controller, use only High quality connectors, motors and batteries. Please, pay careful attention to the following instructions before you start to work with
4、 your new motor and speed controller. Connections: The speed controller can be connected to the motor by direct soldering or with high quality connectors. Always use new connectors, which should be soldered carefully to the cables and insulated with Heat-shrink tubing. It is possible to extend the c
5、ables to the motor battery pack up to a maximum of 8 inches. Deans Ultra or other high quality connectors are recommended for connecting the motor battery pack to the controller. Solder Controller to the Motor wires Solder appropriate connectors to the Battery wires Insulate all Solder connections w
6、ith Heat Shrink Tubing. Plug the JR connector into the receiver throttle channel. When connecting controller to battery pack, care should be taken to ensure that multiple touches of the connectors are not made. Reversing the motor directions is achieved by the exchanging the position of any two wire
7、s connected to the motor or by programming “rotation reverse”. Installing the Controller: Install the speed controller in the model so that it is isolated from vibration and shock, using Velcro or double sided foam tape. Allow space around it for cooling. Make sure that there is sufficient cooling o
8、f the motor and speed controller by ducting air through adequate cooling holes from the outside airflow. Main power packs should be connected at one attempt. Copyright 01/06 Hacker Motor GmbH 1 This Manual: http:/ X-speed controllers have an optimal default setup for A-Motors. Factory default settin
9、gs: Brake: Off Battery type (ESC with BEC): 3S Li-Poly (ca. 8,7V) Battery type (ESC-Opto without BEC): 5S Li-Poly (ca. 14,5V) Under voltage: Reduce power Acceleration : Fast Timing: Auto Frequency: 8KHz Active RPM-Control (Helimode / Governormode): Off Normal start up: When throttle stick is off, co
10、nnect battery pack,switch on the controller (if switch is installed), you will hear one beep for Brake on or two tones for Brake off. For changing the default setup, please read the following manual ESC program procedure It is possible to program the ESC in two different ways: -by using a Computer w
11、ith “Hacker X-Pro USB-Interface” and a special software, which can be acquired, (see then enclosed operating instructions). The USB software offers still additional adjusting parameters: -variable cutoff voltage for LiPo cells -Brake “off“, “soft“, “hard“ -finer gradations in the Motortiming -accele
12、ration in three stages selectable -updates for the X-Pro ESC -programming by throttlestick: With throttle stick at full power, connect the battery and wait for 5 sec. Program mode is entered when you hear two low tones and two high tones. _ _ - - Each time you enter the programming mode you are allo
13、wed to make one change and then you will automatically exit the programming mode. To change more than one parameter you will have to re-enter the programming mode each time. 1. Brake To change the brake function, as soon as you hear the programming tones mentioned above, move the throttle stick to l
14、ow position. Brake function will be inverted. (IE: If brake was on, it now will be off.) To change any of the remaining functions, enter the programming mode as detailed above. Leave the throttle at high position until you are within the five sets of beeps as detailed in each of the choices below. W
15、hen you arrive at the choice you want to make, move the throttle to low position while that series of 5 tones are still being heard. WARNING: the motor will run now by moving the throttlestick! Copyright 01/06 Hacker Motor GmbH 2 This Manual: http:/ Battery type (Voltage Cut-off) NiCd: . . . . . 2 Lipos: (5.8V) . . . . . 3 Lipos: (8.7V) . . . . . Following options only on OPTO-controllers: 4 Lipos: (11.6V) . . . . . 5 Lipos: (14.5V) . . . .
