《单接口nat配置实例》由会员分享，可在线阅读，更多相关《单接口nat配置实例（4页珍藏版）》请在金锄头文库上搜索。
1、单接口 NAT 配置实例拓扑示意：说明:一台路由器只有一个接口时，如何实现 NAT/PAT 的操作。如图所示：R5 相关配置：方法一(较复杂，影响速度)：r5:enconf thost r5no ip domain-lookupdefa int e0/0defa int s0/0defa int s0/1defa int s0/2defa int s0/3no int loop0line con 0exec-time 0 0 logg syexitint loop0ip add 172.16.1.1 255.255.255.255ip nat insideip policy route-map
2、 kxy-nat172.16.1.1/32 192.168.1.254/16 secondaryISP218.87.18.20/26218.87.18.1/26E0/0R5PCa PCn192.168.1.1/16 192.168.1.100/16Loopback0SW1int e0/0ip add 192.168.1.254 255.255.0.0 secondaryip add 218.87.18.20 255.255.255.192 ip nat outsideno shutdownip policy route-map no-routeexitip nat inside source
3、list 10 int e0/0 overloadip route 0.0.0.0 0.0.0.0 218.87.18.1 access-list 10 permit 192.168.0.0 0.0.255.255access-list 110 permit ip 192.168.0.0 0.0.255.255 anyroute-map kxy-nat permit 10match ip add 110set ip next-hop 218.87.18.1route-map no-route permit 10match ip add 110set int loop0 end主要语句相关解释
4、(注意顺序 )：int loop0 ip add 172.16.1.1 255.255.255.255 ip nat inside -5、inside 接口收到包ip policy route-map kxy-nat -6、匹配策略路由int e0/0ip add 192.168.1.254 255.255.0.0 secondary -1、内网数据包到达该网关接口ip add 218.87.18.20 255.255.255.192 -9、包到达该接口ip nat outside -10、匹配 NAT 并转换ip policy route-map no-route -2、匹配策略路由exit
5、ip nat inside source list 10 pool pool1 overloadip nat pool pool1 218.87.18.20 218.87.18.20 netmask 255.255.255.192ip route 0.0.0.0 0.0.0.0 218.87.18.1 (ip route 0.0.0.0 0.0.0.0 loop0 ?)-12、查路由表access-list 10 permit 192.168.0.0 0.0.255.255 -11、匹配 NAT 流量access-list 110 permit ip 192.168.0.0 0.0.255.2
6、55 any -3、匹配流量route-map kxy-nat permit 10match ip add 110 -7、匹配流量set ip next-hop 218.87.18.1-8、基于策略，包送到 e0/0 口route-map no-route permit 10match ip add 110set int loop0 -4、基于策略，包转交到 loop0 口end注：如果此时 no 掉 ip route 0.0.0.0 0.0.0.0 loop0，则能够转换，可以拼通 ISP 地址 218.87.18.1，但拼不通外网其它地址，且此时不能进行地址转换。方法二(较简单，推荐)：r
7、5:enconf thost r5no ip domain-lookupdefa int e0/0defa int s0/0defa int s0/1defa int s0/2defa int s0/3no int loop0line con 0exec-time 0 0 logg syexitint loop0ip add 172.16.1.1 255.255.255.255ip nat insideip policy route-map kxy-natint e0/0ip add 192.168.1.254 255.255.0.0 secondaryip add 218.87.18.20
8、255.255.255.192 ip nat outsideno shexitip nat inside source list 10 int e0/0 overloadip route 0.0.0.0 0.0.0.0 loop0access-list 10 permit 192.168.0.0 0.0.255.255access-list 110 permit ip 192.168.0.0 0.0.255.255 anyroute-map kxy-nat permit 10match ip add 110set ip next-hop 218.87.18.1end主要语句相关解释 (注意顺序
9、 )：int loop0ip add 172.16.1.1 255.255.255.255ip nat insideip policy route-map kxy-nat -3、匹配策略路由int e0/0ip add 192.168.1.254 255.255.0.0 secondary-1、内网数据包到达该网关接口ip add 218.87.18.20 255.255.255.192 -8、匹配策略路由，把包送出ip nat outside -7、NAT 转换no shexitip nat inside source list 10 int e0/0 overloadip route 0.
10、0.0.0 0.0.0.0 loop0 -2、查路由表，包转到 loop0access-list 10 permit 192.168.0.0 0.0.255.255 -6、匹配 NAT 流量access-list 110 permit ip 192.168.0.0 0.0.255.255 any -4、流量匹配route-map kxy-nat permit 10match ip add 110set ip next-hop 218.87.18.1 -5、策略路由end注：该方法简便，内网能拼通外网，但内网拼不通 ISP 的 218.87.18.1 地址(因为内网的包到达 e0/0 时，查路由
11、表，有路由，包直接发出，没有经过 NAT，但内网私有地址的包到达 ISP 后无法回包)测试：C:ping 202.101.224.68Pinging 202.101.224.68 with 32 bytes of data:Reply from 202.101.224.68: bytes=32 time=5ms TTL=58Reply from 202.101.224.68: bytes=32 time=4ms TTL=58Reply from 202.101.224.68: bytes=32 time=5ms TTL=58Reply from 202.101.224.68: bytes=32 time=5ms TTL=58Ping statistics for 202.101.224.68:Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),Approximate round trip times in milli-seconds:Minimum = 4ms, Maximum = 5ms, Average = 4ms说明：该文经江西省计算机培训学院(http:/ )付金如老师测试通过，同时也欢迎沟通交流。转载请注明出处，谢谢!
