《可靠性测试报告[学习]》由会员分享,可在线阅读,更多相关《可靠性测试报告[学习](5页珍藏版)》请在金锄头文库上搜索。
1、报告汇编Compilation of reports20XX报告文档借鉴学习CZT温州意华通讯接插件有限公司WENZHOU YIHUA COMMUNICATED CONNECTOR CO.,LTD产品测试报告TEST REPORT品名P/N:5223 8P8C 测试项目Test item测试条件Test condition测试要求Test requirement测试结果Test result12345678910电气特性ELECTRICAL接触电阻ContactResistance在232,相对湿度855%的环境中,插头与插座之间的接触电阻Mate applicable plug and ex
2、pose to 232,relative humidity 855%小于45m 45mMax 20m21m20m20m21m19m21m21m19m20m绝缘电阻Insulation Resistance在232,相对湿度855%的环境中,相邻金针之间加上500V DC或1000V AC 1分钟Apply 500V DC or 1000V AC for 1minute between adjacent terminal under condition of 23+2, relative humidity 855%大于1000 M1000 M Min耐压测试Withstand Voltage在2
3、32,相对湿度855%的环境中,在相邻的两个端点要求1000V AC 1分钟;Apply 1000V AC for 1minute between adjacent terminal under condition of 23+2, relative humidity 855%端子与端子间:1000V AC/min;无击穿及飞弧现象Between terminals : 1000V AC/min No breakdownOKOKOKOKOKOKOKOKOKOK机械特性MECHANICAL插入力Insert Force将与之相配合的插头以10mm/S的速度水平插入插座Insert applica
4、ble plug at a rate of 10mm/S小于22NMax 22N14N15N15N15N14N14N15N14N14N15N配合强度Retention Strength将插头从插座中以10mm/S的速度水平拔出Pull out applicable plug at a rate of 10mm/S大于57.83N57.83N MIN100N100N100N100N100N100N100N100N100N100N机械寿命Durability将插头以10次/分的速度水平插入插座再水平拔出,反复插拔750次When rated up to750 cycles repeated at
5、a rate of 10 cycles/min外观、弹性良好Appearance be OKOKOKOKOKOKOKOKOKOKOK测试前与测试后的接触阻抗10mThe contact impedance before and after test10m4m4m4m5m4m5m4m5m5m4m判定SentenceOKOKOKOKOKOKOKOKOKOK审核Checker:蒋甘雨 测试Tester:王光丽 日期Date:2009/08/11CZT温州意华通讯接插件有限公司WENZHOU YIHUA COMMUNICATED CONNECTOR CO.,LTD产品测试报告TEST REPORT品名
6、P/N:5223 8P8C 测试项目Test item测试条件Test condition测试要求Test requirement测试结果Test result12345678910可焊性试验Solderability将产品插到PCB基板上放到焊锡槽里(或波峰焊),温度245+5,时间为4+1秒。Insert the terminal into PCB and then for 41 seconds put in the solder-filled tester at the temperature restrained at 2455金针95%以上有锡、无气泡、虚焊现象,光泽度良好。More
7、 than 95% of the pin is covered by Sn, Appearance be OKOKOKOKOKOKOKOKOKOKOK环境特性ENVIRONMENT耐高温试验Heat Resistance样品在852放置96小时,要求测试前与测试后的接触阻抗能10mPut the samples under the condition of 852 for 96 hours , The contact impedance before and after test10m外观良好Appearance be OKOKOKOKOKOKOKOKOKOKOK要求测试前与测试后的接触阻抗1
8、0mThe contact impedance before and after test10m5m4m4m4m5m5m4m5m4m4m盐雾试验Salt Spray溶液为PH值为6.5-7.2的5%Nacl溶液,连续喷雾。试验温度为352,喷雾时间为 24 小时Expose to following salt mist conditions :concentration : 51 % PH:6.5-7.2,continuous spray 。 temperature : 35 2 , Spray time: 24 hours10倍显微镜观察实验品表面无腐蚀现象。The samples surf
9、ace without cautery to inspect by 10X microscope OKOKOKOKOKOKOKOKOKOK判定SentenceOKOKOKOKOKOKOKOKOKOK审核Checker:蒋甘雨 测试Tester:王光丽 日期Date:2009/08/11CZT温州意华通讯接插件有限公司WENZHOU YIHUA COMMUNICATED CONNECTOR CO.,LTD产品测试报告TEST REPORT品名P/N:5223 8P8C 测试项目Test item测试条件Test condition测试要求Test requirement测试结果Test resu
10、lt12345678910环境特性ENVIRONMENT耐寒性Code resistance test 样品在 -402. 放置96小时,要求测试前与测试后的接触阻抗10mPut the samples under the condition of -402 for 96 hours , The contact impedance before and after test10m要求测试前与测试后的接触阻抗10mThe contact impedance before and after test10m8m7m7m7m8m8m7m7m8m7m温湿度测试Temperature and humid
11、ity test样品在402 和 90 to 95% RH. 放置96小时,要求测试前与测试后的接触阻抗10mPut the samples under the condition of 402 and RH 90 to 95% for 96 hours , The contact impedance before and after test10m要求测试前与测试后的接触阻抗10mThe contact impedance before and after test10m7m7m8m7m7m8m8m7m7m8m判定SentenceOKOKOKOKOKOKOKOKOKOK审核Checker:蒋甘雨 测试Tester:王光丽 日期Date:2009/08/11word可编辑实用文档