《5G 后台操作常用指令汇编》由会员分享，可在线阅读，更多相关《5G 后台操作常用指令汇编（9页珍藏版）》请在金锄头文库上搜索。
1、5G 后台操作常用指令汇编1 基础指令1.1 LTE侧指令1) 打开CA频点配置开关（在CA频点配置开关改造中如果实施的话，则不需要重复执行）MOD ENODEBALGOSWITCH: CaAlgoSwitch=PccAnchorSwitch-0&SccBlindCfgSwitch-0&FreqCfgSwitch-1&AdpCaSwitch-0;2) 配置1800 PCC频点ADD PCCFREQCFG: PccDlEarfcn=1396, PreferredPccPriority=0, PccA4RsrpThd=-105, PccA4RsrqThd=-20, objId=0;3) 增加NR
2、SCG频点配置ADD NRSCGFREQCONFIG: PccDlEarfcn=1396, ScgDlArfcn=636666, ScgDlArfcnPriority=1, NsaDcB1ThldRsrp=-105;4) 配置NR外部小区NREXTERNALCELL: Mcc=460, Mnc=08, GnodebId=764952, CellId=128, DlArfcn=636666, UlArfcnConfigInd=Not configure, PhyCellId=10, Tac=33296, objId=0;5) 打开NSA DC算法开关MOD NSADCMGMTCONFIG: Lo
3、calCellId=21, NsaDcAlgoSwitch=NSA_DC_CAPABILITY_SWITCH-1, NsaDcDefaultBearerMode=SCG_SPLIT_BEARER;6) 增加NR相邻频点ADD NRNFREQ: LocalCellId=21, DlArfcn=636666, UlArfcnConfigInd=Not configure;7) 增加NR邻区关系ADD NRNRELATIONSHIP: LocalCellId=21, Mcc=460, Mnc=08, GnodebId=764952, CellId=128;1.2 NR侧配置1) 配置NR本地小区 A
4、DD NRLOCELL: NrLocalCellId=0, NrLocalCellName=太古里5G-SCDHLS5HM3CH-C1, FrequencyBand=n78, UlBandwidth=100 MHz, DlBandwidth=100 MHz, DuplexMode=TDD, CellRadius=10000, SubcarrierSpacing=30, CyclicPrefixLength=Normal Cyclic Prefix, SubframeAssignment=Subframe Assignment 5, WorkMode=Uplink and Downlink, o
5、bjduId=0;2) 配置NR本地小区TRPADD NRLOCELLTRP: NrLoCellTrpId=0, NrLocalCellId=0, TxRxMode=64T64R, SectorEqmId=63, BasebandEqmId=0, MaxTransmitPower=200, CpriCompression=3.2:1 Compression, objduId=0;3) 配置NR小区ADD NRCELL: NrCellId=0, CellName=太古里5G-SCDHLS5HM3CH-C1, NrLocalCellId=0, gNBDuId=764952, CellId=128,
6、 PhysicalCellId=10, FrequencyBand=n78, UlNarfcnConfigInd=Configure, UlNarfcn=636666, DlNarfcn=636666, UlBandwidth=100 MHz, DlBandwidth=100 MHz, DuplexMode=TDD, TrackingAreaId=0, CellActiveState=Activated, CellAdminState=Unblock, objcuId=0;4) 配置NR小区运营商信息ADD NRCELLOP: NrCellId=0, OperatorId=0;5) 邻区配置增
7、加NR外部邻区(ADD NREXTERNALNCELL)ADD NREXTERNALNCELL: Mcc=302, Mnc=220, gNBId=1, CellId=0, PhysicalCellId=0, DlNarfcn=361000;增加NR小区关系(ADD NRCELLRELATION)ADD NRCELLRELATION: NrCellId=0, Mcc=302, Mnc=220, gNBId=1, CellId=0, NCellType=INTRA_FREQ;6) 帧偏置配置LST GNODEBPARAM:;/查询帧偏置MOD GNODEBPARAM: FrameOffset=92
8、160; /修改帧偏置7) 配置NSA DC打开NSA DC开关MOD NRCELLALGOSWITCH: NrCellId=0, NsaDcSwitch=On, NrUlDlDecoupleSwitch=Off;设置DC分流模式MOD NRCELLNSADCCONFIG: NrCellId=0, DlDataScgSplitBearerMode=Transfer Only to SCG, UlDataSplitPrimaryPath=Transfer to MCG, UlDataSplitThreshold=100;8) 激活NR小区去激活NR小区(DEA NRCELL)激活NR小区(ACT
9、 NRCELL)2 基站侧下行峰值商用配置（19B）2.1 通用配置2.1.1 MML参数配置MOD NRDUCELLALGOSWITCH: NrDuCellId=x, Dl256QamSwitch=ON;/ 打开256QAM开关, 默认关MOD NRDUCELLCSIRS: NrDuCellId=x, TrsPeriod=MS40;/ 修改CSIRS周期为40ms, 默认值为20msMOD NRDUCELLPDSCH: NrDuCellId=x, RateMatchSwitch=CSIRS_RATEMATCH_SW-1;/ 打开ratematch，PDSCH可用RE增加，单用户下行吞吐率和小
10、区容量增加。默认关MOD NRDUCELLRSVDOPTPARAM: NrDuCellId=x, ParamId=73, Param1=1;/打开预调度开关，当前版本必须打开预调度否则无法接入，默认关（保留参数，商用时将被替代）MOD GNBRLCPARAMGROUP: RlcParamGroupId=3, RlcMode=AM, UeAmStatusRptProhibitTmr=MS5, gNBAmStatusRptProhibitTmr=MS5, gNBRlcReassemblyTimer=MS5, UeRlcReassemblyTimer=MS5;/ 修改RLC定时器（选开）该命令不是峰
11、值典型配置，建议在跑TCP或者下行存在误码时，修改RLC的定时器，默认值定时器均为40msMOD NRDUCELLRSVDOPTPARAM: NrDuCellId=X, ParamId=60, Param1=1500; /配置预调度字节（选开），该命令不是峰值典型配置，建议在跑TCP开启，如果开启后出现负增益建议关闭，默认100。2.2 2T4R下行峰值配置修改2T4R组网MOD NRDUCELLRSVDOPTPARAM: NrDuCellId=x, ParamId=80, Param1=0;MOD NRDUCELLRSVDOPTPARAM: NrDuCellId=x, ParamId=131
12、, Param1=0;默认值为0修改CSI测量port数MOD NRDUCELLRSVDPARAM: NrDuCellId=x, RsvdU8Param47=2;默认值为2修改下行DMRS相关信息2.3 MOD NRDUCELLPDSCH: NrDuCellId=x, MaxMimoLayerNum=LAYER_4, DlDmrsConfigType=TYPE1, DlDmrsMaxLength=2SYMBOL;/ 默认类型TYPE1，最大流数4流，符号数12.4 4T8R下行峰值配置修改4T8R组网MOD NRDUCELLRSVDOPTPARAM: NrDuCellId=x, ParamId
13、=80, Param1=1;MOD NRDUCELLRSVDOPTPARAM: NrDuCellId=x, ParamId=131, Param1=1;默认值为0修改CSI测量port数MOD NRDUCELLRSVDPARAM: NrDuCellId=x, RsvdU8Param47=3;默认值为2修改下行DMRS相关信息MOD NRDUCELLPDSCH: NrDuCellId=x, MaxMimoLayerNum=LAYER_8, DlDmrsConfigType=TYPE1, DlDmrsMaxLength=2SYMBOL;默认类型TYPE1，最大流数8流，符号数23 基站侧上行峰值商
14、用配置（19B）3.1 通用配置3.1.1 MML参数配置打开PUCCH与PUSCH抢占MOD NRDUCELLRSVDOPTPARAM: NrDuCellId=x, ParamId=75, Param1=1;默认不抢占，参数配置为0，即为不抢占。修改PUCCH格式MOD NRDUCELLPUCCH: NrDuCellId=x, StructureType=LONG_STRUCTURE, Format3RbNum=4, Format1RbNum=RB4;默认长格式，Format3 16个RB，Format1 4个RB.打开上行非连续调度开关MOD NRDUCELLALGOSWITCH: NrD
15、uCellId=x, UlInconsecutiveSchSwitch=UL_NON_CON_SCH_SW-1;默认值为关修改PRACH周期为10msMOD NRDUCELLPRACH: NrDuCellId=x, PrachConfigurationIndex=202;3.2 默认值65535.3.3 2T4R上行峰值配置3.3.1 MML参数配置修改2T4R组网MOD NRDUCELLRSVDOPTPARAM: NrDuCellId=x, ParamId=80, Param1=0;MOD NRDUCELLRSVDOPTPARAM: NrDuCellId=x, ParamId=131, Param1=0;默认值为0修改上行DMRS相关参数MOD NRDUCELLPUSCH: NrDuCellId=X, UlDmrsType=TYPE2, UlAdditionalDmrsPos=NOT_CONFIG, MaxMimoLayerCnt=LAYER_2, UlMimoLayerNumQuota=LAYER_2;3.4 默认配置为DMRS类型为1，最大MIMO为2流。3.5 4T8R上行峰值配置3.5.1 MML参数配置修改4T8R组网MOD NRDUCELLRSVDOPTPARAM: NrDuCellId=x, ParamId=80, Para
