《《复合材料与工程毕业设计外文文献翻译--抛光瓷砖》-公开DOC·毕业论文》由会员分享，可在线阅读，更多相关《《复合材料与工程毕业设计外文文献翻译--抛光瓷砖》-公开DOC·毕业论文（26页珍藏版）》请在金锄头文库上搜索。
1、济南大学毕业设计外文资料翻译毕业设计外文资料翻译题 目 POLISHING OF CERAMIC TILES 抛光瓷砖 学 院 材料科学与工程 专 业 复合材料与工程 班 级 复材0802 学 生 窦文杰 学 号 20080103114 指导教师 邵明梁 二一二年三月二十八日MATERIALS AND MANUFACTURING PROCESSES, 17(3), 401413 (2002)POLISHING OF CERAMIC TILESC. Y. Wang,* X. Wei, and H. YuanInstitute of Manufacturing Technology, Guangd
2、ong University ofTechnology, Guangzhou 510090, P.R. ChinaABSTRACTGrinding and polishing are important steps in the production of decorative vitreous ceramic tiles. Different combinations of finishing wheels and polishing wheels are tested to optimize their selection. The results show that the surfac
3、e glossiness depends not only on the surface quality before machining, but also on the characteristics of the ceramic tiles as well as the performance of grinding and polishing wheels. The performance of the polishing wheel is the key for a good final surface quality. The surface glossiness after fi
4、nishing must be above 208 in order to get higher polishing quality because finishing will limit the maximum surface glossiness by polishing. The optimized combination of grinding and polishing wheels for all the steps will achieve shorter machining times and better surface quality. No obvious relati
5、onships are found between the hardness of ceramic tiles and surface quality or the wear of grinding wheels; therefore, the hardness of the ceramic tile cannot be used for evaluating its machinability.Key Words: Ceramic tiles; Grinding wheel; Polishing wheelINTRODUCTIONCeramic tiles are the common de
6、coration material for floors and walls ofhotel, office, and family buildings. Nowadays, polished vitreous ceramic tiles are more popular as decoration material than general vitreous ceramic tiles as they can*Corresponding author. E-mail: 401Copyright q 2002 by Marcel Dekker, Inc. have a beautiful gl
7、oss on different colors. Grinding and polishing of ceramic tilesplay an important role in the surface quality, cost, and productivity of ceramic tilesmanufactured for decoration. The grinding and polishing of ceramic tiles arecarried out in one pass through polishing production line with many differ
8、entgrinding wheels or by multi passes on a polishing machine, where differentgrinding wheels are used.Most factories utilize the grinding methods similar to those used for stonemachining although the machining of stone is different from that of ceramic tiles.Vitreous ceramic tiles are thin, usually
9、58mm in thickness, and are a sinteredmaterial,which possess high hardness, wear resistance, and brittleness. In general, thesintering process causes surface deformation in the tiles. In themachining process, theceramic tiles are unfixed and put on tables. These characteristics will cause easybreakag
10、e and lower surface quality if grinding wheel or grinding parameters areunsuitable. To meet the needs of ceramic tiles machining, the machinery, grindingparameters (pressure, feed speed, etc.), and grinding wheels (type and mesh size ofabrasive, bond, structure of grinding wheel, etc.) must be optim
11、ized.Previous works have been reported in the field of grinding ceramic andstone1 4. Only a few reports have mentioned ceramic tile machining5 8, wherethe grinding mechanism of ceramic tiles by scratching and grinding was studied. Itwas pointed out that the grinding mechanism of ceramic tiles is sim
12、ilar to that ofother brittle materials. For vitreous ceramic tiles, removing the plastic deformationgrooves, craters (pores), and cracks are of major concern, which depends on themicro-structure of the ceramic tile, the choice of grinding wheel and processingparameters, etc. The residual cracks gene
13、rated during sintering and rough grindingprocesses, as well as thermal impact cracks caused by the transformation of quartzcrystalline phases are the main reasons of tile breakage during processing. Surfaceroughness Ra and glossiness are different measurements of the surface quality. It issuggested
14、that the surface roughness can be used to control the surface quality ofrough grinding and semi-finish grinding processes, and the surface glossiness toassess the quality of finishing and polishing processes. The characteristics of thegrinding wheels, abrasive mesh size for the different machining s
15、teps, machiningtime, pressure, feed, and removing traces of grinding wheels will affect theprocessing of ceramic tiles9.In this paper, based on the study of grinding mechanisms of ceramic tiles, themanufacturing of grinding wheels is discussed. The actions and optimization ofgrinding and polishing wheels for each step are studied in particular for manualpolis
