《部分车型车身反光标识粘贴式样示例（some car body reflective logo sticker style sample）》由会员分享，可在线阅读，更多相关《部分车型车身反光标识粘贴式样示例（some car body reflective logo sticker style sample）（12页珍藏版）》请在金锄头文库上搜索。
1、部分车型车身反光标识粘贴式样示例（Some car body reflective logo sticker style sample）Some car body reflective logo sticker style sampleI. PrefaceIn recent years, with the increase of high-grade highways and the increasing speed of vehicles, accidents such as rear end collision or side collision occur at night and ot
2、her low visibility conditions. In order to effectively reduce the accidents and reduce accidents serious consequences, promulgated in China in December 21, 2002 the public safety industry standard body reflective logo (GA 406-2002), which was released in October 2003 first amendments, the body refle
3、ctive logo material color, inverse basic requirements of main technical parameters of the reflection coefficient and etc. body reflective logo paste made regulations. Promulgated in 2004, the national standard motor vehicle safety technical conditions (GB7258-2004), to further clarify the need to pa
4、ste the body reflective logo models. In order to strengthen source management, with the implementation of standards, the national development and Reform Commission in 2005 will be a body reflective logo into the content of automotive products announcement review, according to the requirements for no
5、t sticking models is not the notice review by the national quality inspection administration; on 2005 issued the No. 137th announcement, the products included in the scope of compulsory product certification since December 1, 2005, the implementation of 3C certification, December 1, 2006 execution e
6、xamination; 2006, Ministry of Public Security Traffic Management Bureau issued the emergency notice on strengthening the safety protection device of motor vehicle and body reflective logo and other management work (bus duct 2006 No. 161), some provinces and cities have formally entered the implement
7、ation stage. From the current situation of application, the main problem at present is that the body is not reflective, labeling, paste is not standardized, not in accordance with the requirements of compliance with the standard requirements of the body reflective materials. The reflective film mate
8、rial properties, especially the retroreflective coefficient is far less than the standard body reflective logo (GA406-2002) requirements for a grade reflective film or two grade reflective film, some body reflective logo and even the use of license plate reflective film or simply use the brush red p
9、aint instead. Did not play its due role, to improve the safety of night driving with little success. In view of this, the body of the reflective logo, paste, identification and other recommendations, aimed at graphic and text written instructions to guide the specification of the body reflective log
10、o paste and quality control.Two, paste Generic requirements1. The rear body light mark shall reflect the width of the rear part of the vehicle as far as possible. The minimum height from the ground is 380mm. The total length of the rear part of the vehicle (without the spacer) shall not be less than
11、 80% of the width of the rear part of the vehicle (the rear body light mark is not allowed to be interrupted in principle).2, the total length of the side body reflective logo should not be less than the length of 50%.3, the side body reflective logo allows interruption, but each successive paragrap
12、h, any color material length shall not be less than 300 mm + 150 mm, and contains red and white body reflective marking material at least one unit. Under special circumstances, red and white units are allowed to be pasted separately, but should be kept in red and white, and the length of each succes
13、sive segment shall be no less than 100mm. The total length of the side body reflective logo (without spacer part) should not be less than 50% of the length;4, when using a primary reflective film material, the sum of the area between the reflector and the back reflector shall not be less than 0.1m2.
14、 When the two stage reflective film material is used, the sum of the area of the reflector and the back reflector shall not be less than 0.2m2.5, body reflective material for red and white stripes reflective material, its width should be no less than 50mm (common specifications for 50mm, 75mm, 100mm
15、).6, because red is a warning color, but the reverse coefficient is usually lower than the same level of white reflective material, it is recommended to use red units than white units longer body reflective materials.7, when you can not paste 50 mm body logo, you can parallel paste two 25 mm wide bo
16、dy logo.8. The material should be firmly and reliably bonded to the surface of the car body. After pasting, the vehicle shall be coordinated with the appearance of the vehicle, and the horizontal direction shall be used as much as possible.9, the body surface can not be directly pasted reflective film material, the reflective film material should be affixed to a certain stiffness, strength, anti-aging of the bar liner, and then the ba
