《hauwei OSPF Configuration Command Handbook》由会员分享，可在线阅读，更多相关《hauwei OSPF Configuration Command Handbook（36页珍藏版）》请在金锄头文库上搜索。
1、Huawei OSPF Command LineOSPF Configuration Command HandbookRevision HistoryRevDateAuthorDescription1.005/05/2001ShinyThe first draft1.105/28/2001Shiny Adjust the parameters of the command distribute-list in/out Change the command qos-enable to mpls traffic-eng area1.206/11/2001Shiny Adjust one param
2、eter of the command distribute-list in/out Modify a parameter range mistake of the command ip ospf network Update some explanation of the command cost-metric2.006/20/2001Shiny Add two new commands ospf-overflow-limit area host rename the command cost-metric to ospf auto-cost modify the no form of so
3、me commands including: area virtual-link, redistribute, default information-originate and so on. Update the explanation of some show commands.2.107/05/2001Shiny Modify a mistake of command mode of the command neighbor2.207/25/2001Shiny Make small modification of the form of the show commands as per
4、cisco specification.3.008/01/2001Shiny Modify the match item of redistribute command Modify the form of the distribute in/out, redistribute command to make it clearer.3.108/13/2001Shiny Add two parameters of the command ospf-maximum-routes Remove the redundant information of the command network3.208
5、/14/2001Rahul Modify the passive command style.1.area authentication52.area default-cost53.area host64.area nssa65.area range76.area stub87.area virtual-link88.clear ip patible rfc15831110.debug ip ospf hot-standby1111.debug ip ospf event1212.debug ip ospf lsa-generation1213.debug ip ospf packet1214
6、.debug ip ospf spf1315.default-information originate1316.default-metric1417.default-tag1418.default-type1419.distribute-list in1420.distribute-list out1521.enable opaque-lsa1722.ip ospf authentication-key1723.ip ospf cost1824.ip ospf dead-interval1825.ip ospf hello-interval1926.ip ospf message-diges
7、t-key1927.ip ospf mtu-ignore2028.ip ospf network2029.ip ospf priority2130.ip ospf retransmit-interval2131.ip ospf transmit-delay2232.log-enable2233.maximum-paths2334.mpls traffic-eng work area2437.no area2538.ospf auto-cost2639.ospf-maximum-routes2640.ospf-overflow-limit2641.passive-interface2742.pr
8、eference2743.redistribute2844.router-id3045.router ospf3146.show ip ospf3147.show ip ospf border-routers3148.show ip ospf cumulative3249.show ip ospf database3250.show ip ospf error3251.show ip ospf interface3252.show ip ospf neighbor3353.show ip ospf nexthop3354.show ip ospf request-list3455.show i
9、p ospf retransmit-list3456.show ip ospf routing3557.show ip ospf virtual-links3558.summary-address351. area authenticationTo enable authentication for an OSPF area, use the area authentication router configuration command. To remove an areas authentication specification or a specified area from the
10、configuration , use the no form of this command.Formatarea area-id authentication message-digestno area area-id authenticationParameters listarea-id: Identifier of the area for which authentication is to be enabled. The identifier can be specified as either a decimal value or an IP address.message-d
11、igest:(Optional) Enables MD5 or HMAC-MD5 authentication on the area specified by area-id.DefaultNo authentication. Command modeOSPF configuration mode.Related commandsip ospf authentication-keyip ospf message-digest-keyno area 2. area default-costTo specify a cost for the default summary route sent
12、into a stub or NSSA area, use the area default-cost router configuration command. To remove the assigned default route cost, use the no form of this command.Formatarea area-id default-cost costno area area-id default-costParameters listarea-id: Identifier for the stub or NSSA area. The identifier ca
13、n be specified as either a decimal value or an IP address.cost:Cost for the default summary route used for a stub or NSSA area. The acceptable value is a 24-bit number. DefaultThe default value of cost is 1.Command modeOSPF configuration mode.Related commandsarea stubno area 3. area hostTo add one h
14、ost route to OSPF link database, To remove this config. use the no form of this command.Formatarea area-id host host-ip costno area area-id host host-ipParameters listarea-id: Identifier of the area for which host route is to be configured. The identifier can be specified as either a decimal value or an IP address.host-ip: The destination ip address of the host route.cost: T
