《EPONV2R1常用命令》由会员分享，可在线阅读，更多相关《EPONV2R1常用命令（7页珍藏版）》请在金锄头文库上搜索。
1、1 安装ONULED 指示灯： 1) Power-长亮 2) Run-闪亮3) PON-长亮 (如果PON灯是灭的，请检查ONU处接收光功率)4) Link/Ack 长亮-用户电脑开机 闪亮-以太网端口收发数据 2 GFA6700的命令行帮助1) 输入 list 命令查找关键字中包含某个字符串的命令，如 list mac EPON_V2R1(config)#list mac delete forward-entry drop mac vlan delete forward-entry mac vlan forward-entry mac vlan 。 show onu information
2、mac show sysmacEPON_V2R1(config)#2) 输入一个关键字加空格后，可以输入“？”来查看以该关键字开头的所有可用命令，如 interface ， 提示如下： EPON_V2R1(config)#interface ethernet Config ethernet interface trunk Config Trunk interface vlan Config multicast vlan interfaceEPON_V2R1(config)#interface3) 输入部分关键字后，不加空格，直接键入?，可以列出所有以输入的字符串开头的关键字，如：interfa
3、,系统提示如下： EPON_V2R1(config)#interfa interface Select an interface to config4) 输入部分关键字后，不加空格，直接键入，则系统自动补齐关键字的剩余部分，如果存在多个以已输入字符串开头的关键字，系统则列出所有可用关键字。如下所示： EPON_V2R1(config)#inteEPON_V2R1(config)#interface EPON_V2R1(config)#onuonu onu-pon onu-registerEPON_V2R1(config)#onu 3 EPON业务开通流程：1) OLT加电2) ONU注册ONU
4、前面板的PON灯亮ONU的接收光功率范围要求(-8dBm到-24dBm)3) 使用串口线访问OLT(波特率9600) 使用命令show onu-list查看ONU列表 使用命令show online-onu查看的ONU4) 配置OLT上的VLAN业务 创建VLAN 添加端口5) 给OLT配置公网地址和默认网关 interface vlan manage ip address 192.168.2.100/24 exit ip route 0.0.0.0/0 192.168.2.2546) 配置ONU的上下行带宽 onu downlink-policer pon 5/1 bandwidth cla
5、ss 2 delay low assured-bw 180000 best-effort-bw 180000 up 1 bandwidth class 2 delay low assured-bw 180000 best-effort-bw 180000 down 1 exit7) 配置ONU上的vlan业务 onu 5/1/1 vlan dot1q_add 100 vlan dot1q_port_add 100 1 2 vlan dot1q_port_add 100 3 1 exit8) 配置ONU上的端口限速 onu 5/1/1 port ingress_rate 1 0 8000 por
6、t egress_rate 1 8000 exit9) 保存OLT和ONU的配置 save onu 5/1/1 mgt config save exit 4 OLT 配置命令1 ) Vlan配置 interface vlan *1 add port tagged|untagged delete port tagged|untagged ip address undo ip address *1 exit2) 网关设置 ip route 0.0.0.0/0 192.168.2.2543) ONU 带宽设置 onu down-link policer pon 5/1 bandwidth class
7、 2 delay low assured-bw 180000 best-effort-bw 180000 up 1 bandwidth class 2 delay low assured-bw 180000 best-effort-bw 180000 down 1 exit4) 以太网接口配置 Interface 1/1 Show Show statistics Clear statistics exit 5) ARP和MAC地址表操作 Show arp Clear arp Show forward-entry *1 pon 5/1 show fdbentry mac exit 6) SNMP
8、网管命令 service snmp enable service snmp trap enable config snmp trapreceiver add 77.235.14.14 version v1 community public 7) 其它命令 Save Rebootconfig hostname GFA6700 show version show slot show system time set system time show onu-list show online_onu show onu-version pon 5/1 show onu-list show online_
9、onu show onu-version update onu file exit download ftp app . olt|ONU) download ftp driver . show running-config (memory) show running-config interface vlan show config-file erase config-file erase alarm log user add|delete user role （only admin user have this right，and must login using a password) c
10、onfiue login-authentication enable 5 告警1) ONU注册告警 2007-12-24,12:02:51 10mkr_dom17/1 first register 11404: 2008-08-20,01:49:35 V2R1-ONU-42003 not present: REPORT TIMEOUT11405: 2008-08-20,01:49:36 V2R1-ONU-42003 re-register 2) ONU 掉电告警 11433: 2008-08-20,01:53:07 V2R1-ONU-41002 power off 11435: 2008-08
11、-20,01:53:21 V2R1-ONU-41002 power on3) ONU端口up-down告警 11415: 2008-08-20,01:51:38 V2R1-ONU-41002 interface eth1/2 linkdown11569: 2008-08-20,02:10:59 V2R1-ONU-41002 interface eth1/2 linkup4) 管理操作 11741: 2008-08-20,07:04:08 V2R1-ONU-42002 not present: OAM LINK DISCONN11742: 2008-08-20,07:04:33 V2R1-ONU-41002 not present: HOST REQUEST5) OLT 重启 11772: 2008-08-20,07:07:49 Epon V2R1 pon4/1 firmware load success11773: 2008-08-20,07:07:49 Epon V2R1 pon4/1 DBA load succes
