《冲压模具-冲压名称类英汉对照》由会员分享，可在线阅读，更多相关《冲压模具-冲压名称类英汉对照（24页珍藏版）》请在金锄头文库上搜索。
1、冲压模具冲压模具- -冲压名称类英汉对照冲压名称类英汉对照plain die 简易模pierce die 冲孔模forming die 成型模progressive die 连续模gang dies 复合模shearing die 剪边模riveting die 铆合模pierce 冲孔forming 成型(抽凸,冲凸)draw hole 抽孔bending 折弯trim 切边emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stret
2、ch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号)shearing 剪断tick-mark nearside正面压印tick-mark farside 反面压印extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight
3、 重量total wt.总重量punch wt.上模重量1 / 1各式模具分类用语英汉对照各式模具分类用语英汉对照landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具center-gated mold 中心浇口式模具 loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold 活动式模具clod hobbing 冷挤压制模 louvering die 百叶窗冲切模compos
4、ite dies 复合模具 manifold die 分歧管模具counter punch 反凸模 modular mold 组合式模具double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模 palletizing die 叠层模family mold 反套制品模具 plaster mold 石膏模blank through dies 漏件式落料模
5、 porous mold 通气性模具duplicated cavity plate 复板模 positive mold 全压式模具fantail die 扇尾形模具 pressure die 压紧模fishtail die 鱼尾形模具 profile die 轮廓模flash mold 溢料式模具 progressive die 顺序模gypsum mold 石膏铸模 protable mold 手提式模具hot-runner mold 热流道模具 prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模lancing die 切口模 raisi
6、ng(embossing) 压花起伏成形re-entrant mold 倒角式模具 sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套 single cavity mold 单腔模具solid forging die 整体锻模 split forging die 拼合锻模split mold 双并式模具 sprueless mold 无注道残料模具squeezing die 挤压模 stretch form
7、die 拉伸成形模sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具 trimming die 切边模unit mold 单元式模具 universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 轭型模模具英语解释模具英语解释一、入水：gate进入位：gate location水口形式：gate type1 / 1大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diame
8、ter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round (full/half runner)流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：li
9、ne lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边 L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位
10、：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate1 / 1缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sp
11、rue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：ang
12、le from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting1 / 1回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位
13、出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient
14、 rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrode模具相关英语模具相关英语 1 1padding block 垫块stepping bar 垫条upper die base 上模座lower die base 下模座upper supporting blank 上承板upper padding plate blank 上垫板spare dies 模具备品spring 弹簧bolt 螺栓document folder 活页夹file folder 资料夹to put
15、 file in order 整理资料spare tools location 手工备品仓first count 初盘人first check 初盘复棹人second count 复盘人second check 复盘复核人equipment 设备waste materials 废料work in progress product 在制品casing = containerazation装箱1 / 1quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page 第一联
16、filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name 单据名称This sheet and physical inventory list will be sent to accounting department together (Those ofNHK will be sent to financial department)本表请与盘点清册一起送
17、会计部(NHK 厂区送财会部)Application status records of year-end physical inventory List and physical inventory card年终盘点卡与清册使用状况明细表blank and waste sheet NO.空白与作废单号plate 电镀mold 成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample 样品incoming material to be inspected进货待验descr
18、iption 品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes 会议记录meeting type 会别distribution department分发单位location 地点chairman 主席present members 出席人员subject 主题conclusion 结论decision items 决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by
19、核准/审核/承办PCE assembly production schedule sheetPCE 组装厂生产排配表model 机钟work order 工令revision 版次remark 备注1 / 1production control confirmation生产确认checked by 初审approved by 核准department 部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or rewor
20、ked待验或重工total 合计cause description 原因说明part number/ P/N 料号type 形态item/group/class 类别quality 品质prepared by 制表notes 说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量 difference quantity差异量cause analysis 原因分析raw materials 原料materials 物料fini
21、shed product 成品semi-finished product 半成品packing materials 包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods 处理品warehouse/hub 仓库on way location 在途仓oversea location 海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/palle
22、t 栈板tox machine 自铆机wire EDM 线割EDM 放电机coil stock 卷料sheet stock 片料tolerance 工差1 / 1score=groove 压线cam block 滑块pilot 导正筒trim 剪外边pierce 剪内边drag form 压锻差pocket for the punch head挂钩槽slug hole 废料孔feature die 公母模expansion dwg 展开图radius 半径shim(wedge)楔子torch-flame cut 火焰切割set screw 止付螺丝form block 折刀stop pin 定
23、位销round pierce punch=die button圆冲子shape punch=die insert 异形子stock locater block 定位块under cut=scrap chopper清角active plate 活动板模具相关英语模具相关英语 2 2baffle plate 挡块cover plate 盖板male die 公模female die 母模groove punch 压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block 衬套insert 入块club car 高尔夫球
24、车capability 能力parameter 参数factor 系数phosphate 皮膜化成viscosity 涂料粘度alkalidipping 脱脂main manifold 主集流脉1 / 1bezel 斜视规blanking 穿落模dejecting 顶固模demagnetization 去磁;消磁high-speed transmission高速传递heat dissipation 热传rack 上料degrease 脱脂rinse 水洗alkaline etch 龄咬desmut 剥黑膜D.I. rinse 纯水次Chromate 铬酸处理Anodize 阳性处理seal 封
25、孔revision 版次part number/P/N 料号good products 良品scraped products 报放心品defective products 不良品finished products 成品disposed products 处理品barcode 条形码flow chart 流程窗体assembly 组装stamping 冲压molding 成型spare parts=buffer 备品coordinate 坐标dismantle the die 折模auxiliary fuction 辅助功能poly-line 多义线heater band 加热片thermoco
26、uple 热电偶sand blasting 喷沙grit 砂砾derusting machine 除锈机degate 打浇口dryer 烘干机induction 感应induction light 感应光response=reaction=interaction感应ram 连杆1 / 1edge finder 巡边器concave 凹convex 凸short 射料不足nick 缺口speck 瑕疪shine 亮班splay 银纹gas mark 焦痕delamination 起鳞cold slug 冷块blush 导色gouge 沟槽;凿槽satin texture 段面咬花witness
27、line 证示线patent 专利grit 沙砾granule=peuet=grain 细粒grit maker 抽粒机cushion 缓冲magnalium 镁铝合金magnesium 镁金metal plate 钣金lathe 车mill 锉plane 刨grind 磨drill 钻boring 镗blinster 气泡fillet 镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver 铡楔shank 摸柄crank shaft 曲柄轴augular offset 角度偏差velocity 速度production temp
28、o 生产进度现状torque 扭矩spline=the multiple keys花键quenching 淬火tempering 回火annealing 退火1 / 1carbonization 碳化alloy 合金tungsten high speed steel 钨高速的moly high speed steel 钼高速的organic solvent 有机溶剂bracket 小磁导liaison 联络单volatile 挥发性resistance 电阻ion 离子titrator 滴定仪beacon 警示灯coolant 冷却液crusher 破碎机模具工程类plain die 简易模p
29、ierce die 冲孔模forming die 成型模progressive die 连续模gang dies 复合模shearing die 剪边模riveting die 铆合模pierce 冲孔forming 成型(抽凸,冲凸)draw hole 抽孔bending 折弯trim 切边emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料模具相关英语模具相关英语 3 3
30、1 / 1stamp letter 冲字(料号)shearing 剪断tick-mark nearside正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量pu
31、nch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板（顶板）top block 上垫脚punch set 上模座p
32、unch pad 上垫板punch holder 上夹板stripper pad 脱料背板1 / 1up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类p
33、unch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod气垫顶杆trimming punch 切边冲子stiffening rib punch = sting
34、er 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块模具工程常用词汇1 / 1die 模具figure file, chart file图档cutting die, blanking die 冲裁模progressive die, follow (-on)die连续模compound die 复合模punched hole 冲孔panel board 镶块to cutedges=side cut=side scrap切边to bending 折弯to pull, to stretch
35、拉伸Line streching, line pulling线拉伸engraving, to engrave 刻印upsiding down edges 翻边to stake 铆合designing, to design 设计design modification设计变化die block 模块folded block 折弯块sliding block 滑块location pin 定位销lifting pin 顶料销die plate, front board 模板padding block 垫块stepping bar 垫条upper die base 上模座lower die base
36、下模座upper supporting blank 上承板upper padding plate blank 上垫板spare dies 模具备品spring 弹簧bolt 螺栓document folder 文件夹file folder 资料夹to put file in order 整理资料spare tools location 手工备品仓first count 初盘人first check 初盘复棹人second count 复盘人second check 复盘复核人equipment 设备waste materials 废料work in progress product 在制品ca
37、sing = containerazation装箱1 / 1quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page 第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name 单据名称This sheet and phy
38、sical inventory list will be sent to accountingdepartment together (Those of NHK will be sent to financialdepartment)本表请与盘点清册一起送会计部(NHK 厂区送财会部)Application status records of year-end physical inventory List andphysical inventory card 年终盘点卡与清册使用状况明细表blank and waste sheet NO.空白与作废单号plate 电镀mold 成型mater
39、ial for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample 样品incoming material to be inspected进货待验description 品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes 会议记录meeting type 会别distribution department分发单位location 地点chairman 主席present members 出席人员subject
40、 主题conclusion 结论decision items 决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE 组装厂生产排配表model 机锺work order 工令revision 版次1 / 1remark 备注production control confirmation生产确认checked by 初审approved by 核准depart
41、ment 部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total 合计cause description 原因说明part number/ P/N 料号type 形态item/group/class 类别quality 品质prepared by 制表notes 说明year-end physical inventory difference analysis sheet年终盘点
42、差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis 原因分析raw materials 原料materials 物料finished product 成品semi-finished product 半成品packing materials 包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods 处理品ware
43、house/hub 仓库on way location 在途仓oversea location 海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet 栈板tox machine 自铆机wire EDM 线割EDM 放电机coil stock 卷料1 / 1sheet stock 片料tolerance 工差score=groove 压线cam block 滑块pilot 导正筒trim 剪外边pierce 剪内边drag form 压锻差pocket for the punch head
44、挂钩槽slug hole 废料孔feature die 公母模expansion dwg 展开图radius 半径shim(wedge)楔子torch-flame cut 火焰切割set screw 止付螺丝form block 折刀stop pin 定位销round pierce punch=die button圆冲子shape punch=die insert 异形子stock locater block 定位块under cut=scrap chopper清角active plate 活动板baffle plate 挡块cover plate 盖板male die 公模female di
45、e 母模groove punch 压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block 衬套insert 入块club car 高尔夫球车capability 能力parameter 参数factor 系数phosphate 皮膜化成viscosity 涂料粘度alkalidipping 脱脂main manifold 主集流脉bezel 斜视规blanking 穿落模dejecting 顶固模demagnetization 去磁;消磁1 / 1high-speed transmission高速传递heat
46、dissipation 热传rack 上料degrease 脱脂rinse 水洗alkaline etch 龄咬desmut 剥黑膜D.I. rinse 纯水次Chromate 铬酸处理Anodize 阳性处理seal 封孔revision 版次part number/P/N 料号good products 良品scraped products 报放心品defective products 不良品finished products 成品disposed products 处理品barcode 条码flow chart 流程表单assembly 组装stamping 冲压molding 成型sp
47、are parts=buffer 备品coordinate 座标dismantle the die 折模auxiliary fuction 辅助功能poly-line 多义线heater band 加热片thermocouple 热电偶sand blasting 喷沙grit 砂砾derusting machine 除锈机degate 打浇口dryer 烘干机induction 感应induction light 感应光response=reaction=interaction感应ram 连杆edge finder 巡边器concave 凸convex 凹short 射料不足nick 缺口1
48、/ 1speck 瑕?shine 亮班splay 银纹gas mark 焦痕delamination 起鳞cold slug 冷块blush 导色gouge 沟槽;凿槽satin texture 段面咬花witness line 证示线patent 专利grit 沙砾granule=peuet=grain 细粒grit maker 抽粒机cushion 缓冲magnalium 镁铝合金magnesium 镁金metal plate 钣金lathe 车mill 锉plane 刨grind 磨drill 铝boring 镗blinster 气泡fillet 镶;嵌边through-hole for
49、m通孔形式voller pin formality滚针形式cam driver 铡楔shank 摸柄crank shaft 曲柄轴augular offset 角度偏差velocity 速度production tempo 生产进度现状torque 扭矩spline=the multiple keys花键quenching 淬火tempering 回火annealing 退火carbonization 碳化alloy 合金tungsten high speed steel 钨高速的moly high speed steel 钼高速的organic solvent 有机溶剂1 / 1bracke
50、t 小磁导liaison 联络单volatile 挥发性resistance 电阻ion 离子titrator 滴定仪beacon 警示灯coolant 冷却液crusher 破碎机模具工程类plain die 简易模pierce die 冲孔模forming die 成型模progressive die 连续模gang dies 复合模shearing die 剪边模riveting die 铆合模pierce 冲孔forming 成型(抽凸,冲凸)draw hole 抽孔bending 折弯trim 切边emboss 凸点dome 凸圆semi-shearing 半剪stamp mark
51、冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号)shearing 剪断tick-mark nearside正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上1 / 1downward 向下pr
52、ess specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post
53、外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板
54、(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板1 / 1inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承
55、块air cushion plate 气垫板air-cushion eject-rod气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate 上中间板spring box 弹簧箱spri
56、ng-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块塑件&模具相关英文compre sion molding压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控 母模core 模心 公模taper 锥拔leather cloak 仿皮革1 / 1shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping
57、screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具常用塑料英语缩略语英文简称 英文全称 中文全称ABA Acrylonitrile-butadiene-acrylate 丙烯腈/丁二烯/丙烯酸酯共聚物ABS Acrylonitrile-butadiene-styrene 丙烯腈/丁二烯/苯乙烯共聚物AES Acrylonitrile-ethylene-styrene 丙烯腈/乙烯/苯乙烯共聚物AMMA Acrylonitrile/methyl Methacrylate 丙烯腈/甲基丙烯酸甲酯共聚物A
58、RP Aromatic polyester 聚芳香酯AS Acrylonitrile-styrene resin 丙烯腈-苯乙烯树脂ASA Acrylonitrile-styrene-acrylate 丙烯腈/苯乙烯/丙烯酸酯共聚物CA Cellulose acetate 醋酸纤维塑料CAB Cellulose acetate butyrate 醋酸-丁酸纤维素塑料CAP Cellulose acetate propionate 醋酸-丙酸纤维素CE Cellulose plastics, general 通用纤维素塑料CF Cresol-formaldehyde 甲酚-甲醛树脂CMC Car
59、boxymethyl cellulose 羧甲基纤维素CN Cellulose nitrate 硝酸纤维素CP Cellulose propionate 丙酸纤维素CPE Chlorinated polyethylene 氯化聚乙烯CPVC Chlorinated poly(vinyl chloride) 氯化聚氯乙烯CS Casein 酪蛋白CTA Cellulose triacetate 三醋酸纤维素EC Ethyl cellulose 乙烷纤维素EMA Ethylene/methacrylic acid 乙烯/甲基丙烯酸共聚物EP Epoxy, epoxide 环氧树脂EPD Ethyl
60、ene-propylene-diene 乙烯-丙烯-二烯三元共聚物EPM Ethylene-propylene polymer 乙烯-丙烯共聚物EPS Expanded polystyrene 发泡聚苯乙烯ETFE Ethylene-tetrafluoroethylene 乙烯-四氟乙烯共聚物EVA Ethylene/vinyl acetate 乙烯-醋酸乙烯共聚物EVAL Ethylene-vinyl alcohol 乙烯-乙烯醇共聚物FEP Perfluoro(ethylene-propylene) 全氟（乙烯-丙烯）塑料1 / 1FF Furan formaldehyde 呋喃甲醛HDP
61、E High-density polyethylene plastics高密度聚乙烯塑料HIPS High impact polystyrene 高冲聚苯乙烯IPS Impact-resistant polystyrene 耐冲击聚苯乙烯LCP Liquid crystal polymer 液晶聚合物LDPE Low-density polyethylene plastics 低密度聚乙烯塑料LLDPE Linear low-density polyethylene 线性低密聚乙烯LMDPE Linear medium-density polyethylene 线性中密聚乙烯MBS Methacrylate-butadiene-styrene 甲基丙烯酸-丁二烯-苯乙烯共聚物MDPE Medium-density polyethylene 中密聚乙烯MF Melamine-formaldehyde resin 密胺-甲醛树脂1 / 1
