《普通全钢冲模的冲压精度分析外文文献翻译、中英文翻译》由会员分享，可在线阅读，更多相关《普通全钢冲模的冲压精度分析外文文献翻译、中英文翻译（7页珍藏版）》请在金锄头文库上搜索。
1、General all-steel punching dies punching accuracyAccuracy of panel punching part is display the press accuracy of the die exactly. But the accuracy of any punching parts linear dimension and positional accuracy almost depend on the blanking and blanking accuracy,So that the compound mould of compoun
2、d punchings accuracy, is typicalness and representation in the majority.Analyse of the dies accuracy For the analyse of pracyicable inaccuracy during production of dies to inactivation, we could get the tendency when it is augmentation in most time. From this we could analyse the elements. When the
3、new punch dies pt into production to the first cutter grinding, the inaccuracy produced called initial error; if the die grinding more than twenty times, until its discard, the inaccuracy called conventional error; and before the dies discard, the largest error of the last batch permit, called limit
4、ing error. at job site, the evidence to confirm life of sharpening is the higher of the blanking, punched hole or punched parts. Because all finished parts had been blanked ,so it is especially for the compound dies. Therefore, the analyse of burr and measurement is especially important when do them
5、 as enterprise standardization or checked with .The initial error usually is the minimal through the whole life of die. Its magnitude depend on the accuracy of manufacture, quality, measure of the punching part, thickness of panel, magnitude of gap and degree of homogeneity. The accuracy of manufact
6、ure depend on the manufacture process. For the 1 mm thicked compound punching part made in medium steel, the experimental result and productive practice all prove that the burr of dies which produced by spark cutting are higher 25%30% than produced by grinder ,NC or CNC. The reason is that not only
7、the latter have more exact machining accuracy but also the value of roughness Ra is less one order than the formmer, it can be reached 0.025m. Therefore, the dies initial blanked accuracy depends on the accuracy of manufacture, quality and so on. The normal error of the punch die is the practicable
8、error when the fist cutter grinding and the last cutter grinding before the die produce the last qualified product. As the increase of cutter grinding, caused the measure the nature wear of the dies are gradual increasing, the error of punching part increase also, so the parts are blew proof. And th
9、e die will be unused. The hole on the part and inner because the measure of wear will be small and small gradually, and its outside form will be lager in the same reason. Therefore, the hole and inner form in the part will be made mould according to one-way positive deviation or nearly equal to the
10、limit max measure. In like manner, the punching parts appearance will be made mould according to one-way negative deviation or nearly equal to limit mini measure. For this will be broaden the normal error, and the cutter grinding times will be increased, the life will be long. The limit error in pun
11、ching parts are the max dimension error which practicable allowed in the parts with limit error. This kind of parts usually are the last qualified products before the die discard.For the all classes of dies, if we analyse the fluctuate, tendency of increase and decrease and law which appeared in the
12、 dies whole life, we will find that the master of the error are changeless; the error that because the abrade of the cutter and impression will be as the cutter grinding times increased at the same time. And that will cause the error oversize gradually; and also have another part error are unconvent
13、ional , unforeseen. Therefore, every die s error are composed of fixed error, system error, accident error and so on.fixed error At the whole process when the New punching die between just input production to discard, the changeless master error that in qualified part are called fixed error. Its mag
14、nitude is the deviation when the die production qualified products before the first cutter grinding. Also is the initial error, but the die have initial punching accuracy at this time. Because of the abrade of parts, the die after grinding will be change the dimension error. And the increment of dev
15、iation will oversize as the times of cutter grinding. So the punching accuracy after cutter grinding also called “grinding accuracy” and lower tan initial accuracy. The fixed error depend on the elements factor as followed :(1) The material , sorts, structure, (form) dimension, and thick of panelThe
16、 magnitude of punching gap and degree of homogeneity are have a important effect for the dimension accuracy. Different punching process, material, thick of panel, have completely different gap and punching accuracy. A gear H62 which made in yellow brass with the same mode number m=0.34, 2mm thick and had a center hole, when the gap get C=0.5%t (single edge) , and punched with compound punching die, and the dimension accuracy reach
