《Cisco路由器配置实例经典》由会员分享，可在线阅读，更多相关《Cisco路由器配置实例经典（49页珍藏版）》请在金锄头文库上搜索。
1、 .wd.实训报告实训一 路由 根本配置1、实验目的：路由器 根本配置及ip设置2、拓扑构造图Router0 fa0/0: 192.168.11.1 Fa0/1:192.168.1.1Router1 fa0/0: 192.168.11.2 Fa0/1:192.168.2.1Znn1:192.168.1.2Znn2:192.168.2.23、实验步骤Router1Routeren 用户模式 进入特权模式 Router#conf t 特权模式 进入全局模式 Enter configuration commands, one per line. End with CNTL/Z.Router(conf
2、ig)#host rznn1 改名字为 rznn1rznn1(config)#int fa0/0 进入fa0/0端口rznn1(config-if)#ip add 192.168.11.1 255.255.255.0 设置ip地址 rznn1(config-if)#no sh 激活rznn1(config)#int fa0/1rznn1(config-if)#ip add 192.168.1.1 255.255.255.0rznn1(config-if)#no shrznn1(config-if)#exitrznn1(config)#exitrznn1#copy running-config
3、startup-config 保存 Destination filename startup-config? startup-configrznn1#conf trznn1(config)#enable secret password 222 设置密文rznn1#show ip interface b 显示Interface IP-Address OK? Method Status Protocol FastEthernet0/0 192.168.11.1 YES manual up up FastEthernet0/1 192.168.1.1 YES manual up up Vlan1 u
4、nassigned YES manual administratively down downrouter 2outerenRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#host rznn2rznn2(config)#int fa0/0rznn2(config-if)#ip add 192.168.11.2 255.255.255.0rznn2(config-if)#no shrznn2(config)#int fa0/1rznn2(config-if)#ip ad
5、d 192.168.2.1 255.255.255.0rznn2(config-if)#no shRznn2#copy running-config startup-config 保存 Destination filename startup-config? startup-configrznn2(config-if)#exitrznn2(config)#exitrznn2#conf trznn2(config)#enable secret 222rznn2#show ip interface b Interface IP-Address OK? Method Status Protocol
6、FastEthernet0/0 192.168.11.2 YES manual up up FastEthernet0/1 192.168.2.1 YES manual up up Vlan1 unassigned YES manual administratively down down实训二1、远程登录、密码设置及验证为路由器开设telnet端口，PC机可以远程登陆到Rznn3(Router 1)拓扑构造图Router0:192.168.1.1Pc:192.168.1.2步骤 rznn3rznn3enrznn3#conf tEnter configuration commands, one
7、 per line. End with CNTL/Z.rznn3(config)#no ip domain lookuprznn3(config)#line cons 0rznn3(config-line)#password znnrznn3(config-line)#loginrznn3(config-line)#no exec-trznn3(config-line)#logg syncrznn3(config-line)#exitrznn3(config)#int fa0/0rznn3(config-if)#ip add 192.168.1.1 255.255.255.0rznn3(con
8、fig-if)#no shrznn3(config-if)#exitrznn3(config)#line vty 0 4 打通五个端口rznn3(config-line)#password cisco 设置密码rznn3(config-line)#login 保存 rznn3(config-line)#exit4、测试：实训三 命令组1、目的：八条命令 no ip domain lookupline cons 0passwordloginno exec-tlogg syncshow versionreloadcopy running-config startup-configshow cdp
9、neighbors)2、拓扑构造图Router0 fa0/0: 192.168.11.1Router1 fa0/0: 192.168.11.23、步骤rznn1#conf tEnter configuration commands, one per line. End with CNTL/Z.1、rznn1(config)#no ip domain lookup 取消域名查找转换2、rznn1(config)#line cons 0 翻开cons 0端口3、rznn1(config-line)#password znn 设置密码为 znnrznn1(config-line)#login 保存r
10、znn1(config-line)#no exec-t 设置永不超时4、rznn1(config-line)#logg sync 产生日志5、rznn1#show version 显示思科路由系统版本信息Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)T1, RELEASE SOFTWARE (fc2)Technical Support: :/ cisco /techsupportCopyright (c) 1986-2007 by Cisco Systems, Inc.Compile
11、d Wed 18-Jul-07 06:21 by pt_rel_team6、rznn1#show cdp neighbors 查看路由器连接的相邻路由器的相关信息Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - PhoneDevice ID Local Intrfce Holdtme Capability Platform Port IDrznn2 Fas 0/0 139 R C2800 Fas 0/0
12、7、rznn1#copy running-config startup-config 保存刚刚指令Destination filename startup-config? startup-configBuilding configuration.OK8、rznn1#reload 重启路由器Proceed with reload? confirmSystem Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)Copyright (c) 2000 by cisco Systems, Inc.cisco 2811 (MPC860) processor (revision 0x200) with 6
