《自动变速器课程毕业设计外文文献翻译、中英文翻译、外文翻译》由会员分享，可在线阅读，更多相关《自动变速器课程毕业设计外文文献翻译、中英文翻译、外文翻译（11页珍藏版）》请在金锄头文库上搜索。
1、Automatic TransmissionsThe automatic transmission contain several sections by followed.Transmission The transmission is a device that is connected to the back of the engine and sends the power from the engine to the drive wheels. An automobile engine runs at its best at a certain RPM (Revolutions Pe
2、r Minute) range and it is the transmissions job to make sure that the power is delivered to the wheels while keeping the engine within that range. It does this through various gear combinations. In first gear, the engine turns much faster in relation to the drive wheels, while in high gear the engin
3、e is loafing even though the car may be going in excess of 70 MPH. In addition to various forward gear transmission also has a neutral position which disconnects the engine from the drive wheels, and reverse, which causes the drive wheels to turn in the opposite direction allowing you to back .Final
4、ly, there is the Park position. In this position, a latch mechanism (not unlike a deadbolt lock on a door) is inserted into a slot in the output shaft to lock the drive wheels and keep them from turning, thereby preventing the vehicle from rolling. There are two basic types of automatic transmission
5、s based on whether the vehicle is rear wheel drive or front wheel drive. On a rear wheel drive car, the transmission is usually mounted to the back of the engine and is located under the hump in the center of the floorboard alongside the gas pedal position. A drive shaft connects the rear of the tra
6、nsmission to the final drive which is located in the rear axle and is used to send power to the rear wheels. Power flow on this system is simple and straight forward going from the engine, through the torque converter, then through the transmission and drive shaft until it reaches the final drive wh
7、ere it is split and sent to the two rear wheels. On a front wheel drive car, the transmission is usually combined with the final drive to form what is called a transaxle. The engine on a front wheel drive car is usually mounted sideways in the car with the transaxle tucked under it on the side of th
8、e engine facing the rear of the car. Front axles are connected directly to the transaxle and provide power to the front wheels. Planetary Gear Sets Automatic transmissions contain many gears in the various com binations.In a manual transmission, gears slide along the shafts as you move the shift lev
9、er from one position to another, engaging various sized gears as required in order to provide the correct gear ratio. In an automatic transmission, however, the gears are never physically moved and are always engaged to the same gears. This is accomplished through the use of the planetary gear sets.
10、 The basic planetary gear set consists of a sun gear, a ring gear and two or more planet gears, all the remaining in constant mesh. The planet gears are connected to each other through a common carrier which allows the gears to spin on shafts called pinions which are attached to these carrier. One e
11、xample of a way that this system can be used is by connecting the ring gear to the input shaft coming from the engine, connecting the planet carrier to the output shaft, and locking the sun gear so that it cant move. In this scenario, when we turn the ring gear, the planets will walk along the sun g
12、ear (which is held stationary) causing the planet carrier to turn the output shaft in the same direction as the input shaft but at a slower speed causing gear reduction (similar to a car in first gear).If we unlock the sun gear and lock any the two elements together, this will cause all three elemen
13、ts to turn at the same speed so that the output shaft will turn at the same rate of speed as the input shaft. This is like a car that is in third or high gear. Another way that we can use a Planetary gear set is by locking the planet carrier from moving, then applying power to the ring gear which wi
14、ll cause the sun gear to turn in the opposite direction giving us reverse gear. And the illustration on the right shows how the simple system to described above would look in an actual transmission. The input shaft is connected to the ring gear (blue), The Output shaft is connected to the planet car
15、rier (green) which is also can connected to a Multi-disk clutch pack. The sun gear is that connected to a drum (yellow) which is also connected to the other half of the clutch pack. and Surrounding the outside of the drum is a band (red) that can be tightened around the drum when required to prevent
16、 the drum with the attached sun gear from turning.One-Way Clutch A one-way clutch (also known as a sprag clutch) is a device that will allow a component such as ring gear to turn freely in one direction but not in the other. This effect is just like that of a bicycle, where the pedals will turn the wheel when pedaling forward, but will spin free when pedaling the backward. A common place where a one-way clutch is used is in first gear when the shifter is in
