《AP3010DN-AGN设置为普通无线路由器操作步骤》由会员分享，可在线阅读，更多相关《AP3010DN-AGN设置为普通无线路由器操作步骤（9页珍藏版）》请在金锄头文库上搜索。
1、华为AP3010DN-AGN无线AP设定为一般胖AP无线路由器模式操作步骤说明文档1,认识硬件除以上之外,还需要普通网线1条,电脑1台.2,所用到的软件操作系统xp或win7Xmanager4汉化版USB转线驱动TFTP软件3CDaemon汉化版AP升级固件的文档FatAP3X10XN_V200R005C00SPC600.bin3,操作步骤： 第一步,复位AP,刷固件FatAP3X10XN_V200R005C00SPC600.bin第二步,登录AP的WEB管理页面创建WIFI并建立DHCP第三步,创建WAN口并与LAN口关联下面分步详细说明准备软件,依次安装USB转驱动,Xmanager4汉化
2、版,将TFTP软件3CDaemon汉化版复制到C盘,并变更文件夹名称为TFTP,路径如C:TFTP ,把AP 的固件FatAP3X10XN_V200R005C00SPC600.bin复制到C:TFTP目录中给AP接上12V2A的电源,此时不要接POE供电模块,注意！复位后将消除全部配置与密码.等启动完毕后,用尖锐物按下复位口10秒后松开,AP开始重新启动,AP的指示灯变为长亮启动状态,之后指示灯变为闪烁状态完成复位.完成复位后接上USB 转串口线,连接电脑USB口和AP的Console口,打开Xmanager4中的Xshell4,新建会话窗口选择SERIAL配置波特率9600与端口号正确连接成
3、功后会显示Please configure the login password /Enter password:这是初次登录要求设定密码,密码复杂度要求为英文加数字,最小8位,我们暂定密码hua88888填写两次密码后显示如下Enter password:Confirm password:这表示已经成功设定了管理密码,以上设定的密码仅限于连接Console口使用,和WEB管理界面不是同一个密码,WEB管理界面密码下面会提到.使用1条一般使用的网线,一端连接电脑,一端连接AP的ETH/PoE口,此时不要拔掉Console口上的串口线,不要拔掉12V电源,不要连接POE供电模块,配置电脑有线网卡
4、的IP地址为0子网掩码网关 DNS空白不填写,去我的电脑打开C:TFTP目录,打开3CDaemon.EXE点击设置TFTP服务器按钮,按照下图设置路径然后回到Xshell4窗口,会显示Please check whether system data has been changed, and save data in timeConfiguration console time out, please press any key to log on是因为超时登出,需要重新填写密码登录,重新登录后按照以下脚本操作,整个过程不要关闭3CDaemon.EXEsys #键入Enter system v
5、iew, return user view with Ctrl+Z.Huaweiap-mode-switch prepare #键入Info: Prepare is ok, Use ap-mode-switch mand to switch to fit ap.Huaweiap-mode-switch check #键入Info: Ap-mode-switch check ok.Huawei #键入Info: Preparing to upgrade. Please wait a moment .Warning: System will reboot, if you want to switc
6、h to upgrade-assistant-package.Are you sure to execute these operations ? Y/N:y #这里是提示整个过程会重启,键入yInfo: system is rebooting ,please wait.Try hardware rebooting. * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
7、Wele To HUAWEI AP World UBoot V200R005 version-125 DRAM: 128 MBDDR data bus test is OK!Press c or C to Begin DDR Bus Test in 1 Seconds: 0 Flash: 32 MBPCIE: PCIe Clock 40MHzEthernet Mac: B4-15-13-F8-82-20Image: Current Bootup is B Image: Current Bootup is B Current master bootup parameter area is ABo
8、ot Kernel A Address: 0x9f3fb000Boot Kernel B Address: 0x9f840000Press j or J to stop Bus-Test in 1 seconds: 0Bus test starting.PCIE bus test OK.SPI bus test OK.DDR bus test OK.RGMII bus test OK.Bus test ending.Save Bus Test Result SuccessfulPress f or F to stop Auto-Boot in 3 seconds: 0 Unpressing K
9、ernel Image . OKStarting kernel .Booting Atheros AR934xinit_bsp_adapter .OK.mm_init .OK.sched_init .OK.softirq_init .OK.console_init .OK.thread_info_cache_init .OK.fork_init .OK.dbg_late_init .OK.imv_init_plete .OK.Linux version 2.6.34.13-WR4.3.0.0_standard gcc version 4.5.2 #2 PREEMPT Fri Nov 7 17:
10、34:15 CST 2014flash_size passed from bootloader = 32 MBarg 1: console=ttyS0,9600arg 2: root=/dev/mtdblock10arg 3: rootfstype=squashfsarg 4: init=/sbin/initarg 5: mtdparts=ath-nor0:512k,128k,128k,128k,128k,12288k,3072k,512k,128k,128k,12288k,3072k,256k;arg 6: mem=126Math_sys_frequency: cpu apb,ddr apb
11、,cpu-480MHZ,ddr-400MHZ,ahb-240MHZZone PFN ranges: Normal 0x00000000 - 0x00007e00Movable zone start PFN for each nodeearly_node_map1 active PFN ranges 0: 0x00000000 - 0x00007e00Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32004Kernel mand line: console=ttyS0,9600 root=/dev/mtdblock10 rootfstype=squashfs init=/sbin/init
