《中英文外文翻译--PLC和微处理器-精品.精讲》由会员分享，可在线阅读，更多相关《中英文外文翻译--PLC和微处理器-精品.精讲（8页珍藏版）》请在金锄头文库上搜索。
1、Introductions of PLC and MCUA PLC is a device that was invented to replace the necessarysequential relay circuits for machine control. The PLC works by looking at its inputs and depending upon their state, turning on/off its outputs .The user enters a program, usually via software or programmer that
2、 gives the desired results.PLC are used in many “ realworld ”applications. If there is industry present, chances are good that there is a PLC present. If you are involved in machining, packaging, material handling, automated assembly or countless other industries, you are probably already using them
3、. If you are not, you are wasting money and time. Almost any application that needs some type of electrical control has need for PLC.For example, let?s assume thatwhen a switch turns on we want to turn a solenoid on for 5 seconds and then turn it off regardless of how long the switch is on for. We c
4、an do this with a simple external timer. What if the process also needed to count how many times the switch individually turned on? We need a lot of external counters.As you can see, the bigger the process the more of a need we have for a PLC. We can simply program the PLC to count its inputs and tu
5、rn the solenoids on for the specified time.We will take a look at what i s considered to be the “ top 20 ” PLC instructions. It can be safely estimated that with a firm understanding of there instructions one can solve more than 80% of the applications in existence.That,s right, more than 80%! Of co
6、urse we?ll learn more than just these instructions to help you solve almost ALL your potential PLC applications.The PLC mainly consists of a CPU, memory areas, and appropriate circuits to receive input/output data, as shown in Fig. 19.1 We can actually consider the PLC to be a box full of hundreds o
7、r thousands of separate relays, counters, timer and date storage locations. Do these counters, timers, etc. really exist? No, they don?t“ physically exist” but rather they are simulated and can be considered softwarecounters, timers, etc. These internal relays are simulated through bit locations in
8、registers.What does each part do?INPUT RELAYS-(contacts) These are connected to the outside world. They physically exist and receive signals from switches, sensors, etc. Typically they are not relays but rather they are transistors.INTERNAL UTILITY RELAYS-(contacts)These do not receive signals fromt
9、he outside world nor do they physically exist. They are simulated relays and are what enables a PLC to eliminate external relays. There are also some special relays that are dedicated to performing only one task. Some are always on while some are always off. Some are on only once during power-on and
10、 are typically user for initializing data what was stored.COUNTERS These again do not physically exist. They are simulated counters and they can be programmed to count pulses. Typically these counters can count up, down or both up and down. Since there are simulated, they are limited in their counti
11、ng speed. Some manufacturers also include high-speed counters that are hardware based. We can think of these as physically existing. Most timers these counters can count up, down or up and down.TIMERS These also do not physically exist. They come in many varieties and increments. The most common typ
12、e is an on-delay type. Other include off-delay and both retentive and non-retentive types. Increments vary from 1ms through 1s.OUTPUT RELAYS-(coil) These are connected to the outside world. They physically exist and send on/off signals to solenoids, lights, etc They can be transistors, relays, or tr
13、iacs depending upon the model chosen.DATA STORAGE-Typically there are registers assigned to simply store data. There are usually used as temporary storage for math or data manipulation. They can also typically be user power-up they will still have the same contents as before power war removed. Very
14、convenient and necessary!Step 1-CHECK INPUT STATUS-First the PLC takes a look at each input to determine if it is on or off. In other words, is the sensor connected to the first input on? How about the second input? How about the third Itrecords this data into its memory to be used during the next s
15、tep.Step 2-EXECUTE PROGRAM-Next the PLC executes your program one instruction at a time. Maybe your program said that if the first input was on then it should turn on the first output. Since is already knows which inputs are on/off from the previous step, it will be able to decide whether the first
16、output should be turned onbased on the state of the first input. It will store the execution results for use later during the next step.Step 3-UPDATE OUTPUT STSTUS-Finally the PLC updates the status ofoutputs. It updates the outputs based on which inputs were on during the first step and the results of executing your program during the second step. Based on the example in step 2
