《各种系列水轮机设计点计算表》由会员分享，可在线阅读，更多相关《各种系列水轮机设计点计算表（13页珍藏版）》请在金锄头文库上搜索。
1、规格型号叶片装 置角(P综合特性曲线上的设计点正值水轮机设计点n, 1M. (r/minQ1M )(L/s) M(%)An1， (r/minAQ1)(L/s)A n m (%)n =1 n1J+An1，Q1M 二 q+aqn1 T= nM+AnMZD760-LM-4O+501801800860+54-1.4180185484.6 +1001702030830+60-1.1170209081.9+1501702250800+67-1.0170231779ZD760-LM-60+501801800860+54+0.4180185486.4+1001702030830+60+1.1170209084
2、.1+1501702250800+67+1.2170236781.2ZD760-LM-80+501801800860+54+2.2180185488.2+1001702030830+60+2.7170209085.7+1501702250800+67+3.1170231783.1ZD760-LM-10I+5018018008600+1.7180180087.1)+10017020308300+2.3170203085.3+15017022508000+2.6170225082.6ZD760-LMY-1+5018018008600+2.5180180088.520+10017020308300+
3、3.1170203086.1+15017022508000+3.5170225083.5ZD760-LMY-1+5018018008600180180040+100170203083001702030+150170225080001702250规格型号叶片装 置角(P综合特性曲线上的设计点正值水轮机设计点n(r/minQ%)(L/s) M(%)啊 (r/minQ)(L/s)A n，M(%)n = 1 n1J+An1,Q1M 二 q+aq，n1 T= nM+AnMZD760-LMY-1+5018018008600180180060+100170203083001702030+1501702250
4、80001702250ZD760-LMY-1+5018018008600180180080+100170203083001702030+150170225080001702250ZD560-LMY-4+001351070850+32.1-31351102.1820 +50152132084.50+39.6-31521359.681.50 +100150160082.50+48.0-2.5150164880+1501501840800+55.2-2.51501895.277.5ZD560-LMY-6+001351070850+32.1-0.51351102.184.5+50152132084.5
5、0+39.6-0.51521359.6840T C+ 100150160082.50+48.00150164882.5+1501501840800+55.2+0.51501895.280.5ZD560-LMY-8+001351070850+32.1+1.51351102.186.50+50152132084.50+39.6+1.51521359.6860 +100150160082.50+48.0+2.0150164884.5+1501501840800+55.2+2.01501895.282规格型号叶片装 置角(P综合特性曲线上的设计点正值水轮机设计点n, 1M. (r/minQ% )(L/
6、s) M(%)An1， (r/minAQ1)(L/s)A n m (%)n =1 n1J+An1，Q1M 二 q+aqn1 T= nM+AnMZD560-LH-100+001351070850+32.1+1.51351102.186.5 )+50152132084.50+39.6+1.51521359.686+100150160082.50+48.0+21501648.084.5+15。1501840800+55.2+21501895.282ZD560-LH-12O+0013510708500+2.3135107087.3+50152132084.500+2.3152132086.8+1001
7、50160082.500+2.8150160085.3+15015018408000+3.6150184083.6ZD560-LH-140+0013510708500+3.5135107088.5h5152132084.500+3.5152132088+100150160082.500+4150160086.5+15015018408000+5150184085ZD560-LH-16O+0013510708500+4.3135107089.3+50152132084.500+4.3152132088.8+100150160082.500+4.9150160087.4+1501501840800
8、0+5.8150184085.8ZD560-LH-180、+0013510708500+4.5135107089.5)+50152132084.500+4.5152132089规格型号叶片装 置角(P综合特性曲线上的设计点正值水轮机设计点n, 1M. (r/minQ% )(L/s) M(%)An1， (r/minAQ1)(L/s)A n m (%)n =1 n1J+An1，Q1M 二 q+aqn1 T= nM+AnMZD560-LH-180150160082.500+5.2150160087.7+15。15018408000+6.2150184086.2ZD560-LH-20O+0013510
9、708500+4.7135107089.7+50152132084.500+4.7152132089.2+100150160082.500+5.4150160087.9+15015018408000+6.4150184086.4ZD560-LH-225+0013510708500+4.9135107089.95152132084.500+4.9152132089.4+100150160082.500+5.6150160088.1+15015018408000+6.7150184086.7ZD560-LH-25O+0013510708500+5.1135107090.1+50152132084.
10、500+5.1152132089.6+100150160082.500+5.9150160083.4+15015018408000+7.0150184087规格型号综合特性曲线上的设计;艮修正值水轮机设计点n,1M.、 (r/min)Q1M (L/s) M(%)An1， (r/minAQ1)(L/s)A n m (%)n =1 n1M；+An1，Q = 1M Q+Aqn1 T= nM+AnMHL310-WG-2595147086.5-4.7-68.2-990.31401.877.5HL310-WG-3095147086.5-3.9-56.6-7.591.11413.479HL310-WG-3595147086.5-3.4-48.8-6.591.61421.280HL260-WJ-2577125082-2.8-4.5-674.21245.576HL260-WJ-307712508200-4.577125077.5HL260-WJ-357712508200-3.5771250
