《【英国标准word原稿】BS EN 12261996 塑料管道系统.玻璃增强热固性塑料管.验证初期环状物挠曲阻力的试验方法》由会员分享，可在线阅读，更多相关《【英国标准word原稿】BS EN 12261996 塑料管道系统.玻璃增强热固性塑料管.验证初期环状物挠曲阻力的试验方法（15页珍藏版）》请在金锄头文库上搜索。
1、豆丁网：http:/ STANDARDPlastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test method to prove the resistance to initial ring definitionThe European Standard EN 1226 : 1996 has the status of aBritish StandardICS 23.040.20| BS EN1226 : 1996| BS 2782 :| Part 12 :Method 1214E :| 19
2、96|第 1 页 共 14 页豆丁网：http:/ COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 1226 : 1996Committees responsible for thisBritish StandardThe preparation of this British Standard was entrusted to Technical Committee PRI/61, Plastics piping systems and components, upon which the fo
3、llowing bodies were represented:British Gas plcBritish Plastics FederationBritish Plumbing Fittings Manufacturers Association British Valve and Actuator Manufacturers Association Chartered Institution of Water and Environmental Management Department of the Environment (Building Board of Agre ment)De
4、partment of the Environment (Building Research Establishment) Department of TransportElectricity AssociationFederation of Civil Engineering ContractorsHealth and Safety Executive Institute of Building Control Institute of Materials Institution of Civil Engineers Institution of Gas EngineersNational
5、Association of Plumbing, Heating and Mechanical Services ContractorsPipeline Industries GuildPlastics Land Drainage Manufacturers AssociationSociety of British Gas Industries Society of British Water Industries Water Companies AssociationWater Services Association of England and WalesThe following b
6、odies were also represented in the drafting of the standard, through subcommittees and panels:This British Standard, having been prepared under the direction of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on15 December
7、1996BSI 1996The following BSI references relate to the work on this standard:Committee reference PRI/61Draft for comment 93/313471 DCISBN 0 580 26734 2Association of Consulting EngineersEngineering Equipment and Materials Users AssociationInstitution of Mechanical EngineersRAPRA Technology Ltd.Amd.
8、No.DateText affectedAmendments issued since publicationBS EN 1226 : 1996ContentsPage Committees responsible Inside front cover National foreword ii MethodForeword 21Scope32Definitions33Principle34Apparatus35Test pieces56Conditioning57Procedure58Test report6Figures1Schematic diagram of the test arran
9、gement42Schematic diagram of load versus time4BSI 1996iBS EN 1226 : 1996National forewordThis British Standard has been prepared by Technical Committee PRI/61 and is the English language version of EN 1226 : 1996 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test method
10、 to prove the resistance to initial ring deflection, published by the European Committee for Standardization (CEN).It is incorporated into BS 2782 Methods of testing plastics : Part 12 : Reinforced plastics pipes, fittings and valves, as Method 1214E : 1996 for association with related test methods
11、for plastics materials and plastics piping components.This test method has been prepared for reference by other standards under preparation by CEN for specification of reinforced plastics piping systems and components. It has been implemented to enable experience of the method to be gained and for u
12、se for other fresh applications.It is also for use for the revision or amendment of other national standards as practicable, but it should not be presumed to apply to any existing standard or specification which contains or makes reference to a different test method until that standard/specification
13、 has been amended or revised to make reference to this method and adjust any requirements as appropriate.No existing British Standard is superseded by this Method.Warning note. This British Standard, which is identical with EN 1226 : 1996 does not necessarily detail all the precautions necessary to meet the requirements of the Health and Safety at Work etc. Act 1974.
