《ABB robotstudio使用详细步骤》由会员分享，可在线阅读，更多相关《ABB robotstudio使用详细步骤（28页珍藏版）》请在金锄头文库上搜索。
1、word搬运码垛工作站建模1、创建机器人系统2、创建动态输送链3、创建动态夹具4、工作站逻辑连接5、添加IO(设置好需重启)6、示教目标点同步到RAPID7、RAPID编程一、创建机器人系统1、创建空工作站2、导入IRB 260机器人模型3、从布局创建机器人系统，勾选Chinese和709-1网络二、创建动态输送链1、添加输送链并修改位置2、创建600*400*200的物料 并修改位置3、添加一个smart组件4、添加source组件5、设置物料本地原点6、添加LINEMOVER和QUEUE组件7设置LINEMOVER属性8、添加面传感器组件9、设置输送链不能被传感器检测10、设置SC_输送链
2、的属性连接11、设置信号连接12、添加信号处理组件，用于检测传感器下降沿13、传感器下降沿触发source进展copy第四行有误14、传感器与SC输送链的输出联系15、添加仿真开始完毕组件，用于激活传感器16、添加置位复位组件，对仿真开始完毕信号进展保持17、18、进展仿真设定 选择SC输送链 进展验证三、创建动态夹具1、先制作一个吸盘模型，然后设置成工具，并安装到机器人法拉盘2、添加SMART组件3、添加ATTACHER和DETACHER组件4、设置属性5、添加一个线传感器组件6、线传感器设置属性7、设置吸盘工具不能被传感器检测8、把线传感器安装到吸盘不更新位置，保持当前位置9、设置属性连接
3、10、添加信号与连接11、添加信号处理取非和锁定组件12、继续信号连接13、添加一个示教物料14、应用手动线性验证SC_工具四、工作站逻辑连接五、参考代码MODULE MainMoudlePERS tooldata tGrip:=TRUE,0,0,200,1,0,0,0,25,0,0.00109327,116.889,1,0,0,0,0,0,0;！吸盘工具数据 PERS loaddata LoadEmpty:=0.01,0,0,1,1,0,0,0,0,0,0; PERS loaddata LoadFull:=40,0,0,50,1,0,0,0,0,0,0;！有效载荷数据PERS robtarg
4、et pHome:=1620.00,-0.00,1331.59,1.27986E-06,-0.707107,-0.707107,1.27986E-06,0,0,1,0,9E+09,9E+09,9E+09,9E+09,9E+09,9E+09;！基准点 PERS robtarget pActualPos:=1620,-1.87531E-14,1331.59,1.27986E-06,-0.707107,-0.707107,1.27986E-06,0,0,1,0,9E+09,9E+09,9E+09,9E+09,9E+09,9E+09;！实际点PERS robtarget pPick1:=1488.00
5、7792464,376.826660408,476.964684195,0,0.707106307,0.707107256,0,0,0,1,0,9E9,9E9,9E9,9E9,9E9,9E9;！1路拾取目标点PERS robtarget pPlace1:=-292.446,1263.27,55.4492,0,0.707107,0.707106,0,1,0,2,0,9E+09,9E+09,9E+09,9E+09,9E+09,9E+09;！1路放置基准点PERS robtarget pBase1_0:=-292.446294945,1263.272085268,55.449220723,0,0.7
6、07107387,0.707106176,0,1,0,2,0,9E9,9E9,9E9,9E9,9E9,9E9;！1路放置0度姿态 PERS robtarget pBase1_90:=-391.976797324,1362.469634994,55.449159414,0,1,-0.000030621,0,1,0,3,0,9E9,9E9,9E9,9E9,9E9,9E9;！1路放置90度姿态 PERS robtarget pPick2:=1488.013130905,-358.406014736,476.965039287,0,0.707106307,0.707107256,0,-1,0,0,0,
7、9E9,9E9,9E9,9E9,9E9,9E9; PERS robtarget pPlace2:=-317.378,-1857.99,55.449,0,0.707108,0.707106,0,-2,0,-1,0,9E+09,9E+09,9E+09,9E+09,9E+09,9E+09; PERS robtarget pBase2_0:=-317.378137718,-1857.993871961,55.448967354,0,0.707107745,0.707105817,0,-2,0,-1,0,9E9,9E9,9E9,9E9,9E9,9E9; PERS robtarget pBase2_90:
8、=-407.525988074,-1755.902485322,55.449282402,0,1,-0.000031217,0,-2,0,0,0,9E9,9E9,9E9,9E9,9E9,9E9; PERS speeddata MinSpeed:=1000,300,5000,1000; PERS speeddata MidSpeed:=2500,400,5000,1000; PERS speeddata MaxSpeed:=4000,500,5000,1000;！搬运速度定义 PERS bool bPalletFull1:=FALSE; PERS bool bPalletFull2:=FALSE
9、;！逻辑布尔量，拾取后为UE，放置后为FALSE PERS num nCount1:=1; PERS num nCount2:=1;！输送链计数 PROC Main() rInitAll; WHILE TRUE DO IF diBoxInPos1=1 AND diPalletInPos1=1 AND bPalletFull1=FALSE THEN rPick1; rPlace1; ENDIF IF diBoxInPos2=1 AND diPalletInPos2=1 AND bPalletFull2=FALSE THEN rPick2; rPlace2; ENDIF WaitTime 0.1;
10、 ENDWHILE ENDPROC PROC rInitAll() Reset doGrip; pActualPos:=CRobT(tool:=tGrip); pActualPos.trans.z:=pHome.trans.z; MoveL pActualPos,MinSpeed,fine,tGripWObj:=wobj0; MoveJ pHome,MidSpeed,fine,tGripWObj:=wobj0; bPalletFull1:=FALSE; nCount1:=1; bPalletFull2:=FALSE; nCount2:=1; ENDPROC PROC rPick1() Move
11、J Offs(pPick1,0,0,400),MaxSpeed,z50,tGripWObj:=wobj0; MoveL pPick1,MinSpeed,fine,tGripWObj:=wobj0; Set doGrip; WaitTime 0.3; GripLoad LoadFull; MoveL Offs(pPick1,0,0,400),MinSpeed,z50,tGripWObj:=wobj0; ENDPROC PROC rPick2() MoveJ Offs(pPick2,0,0,400),MaxSpeed,z50,tGripWObj:=wobj0; MoveL pPick2,MinSp
12、eed,fine,tGripWObj:=wobj0; Set doGrip; WaitTime 0.3; GripLoad LoadFull; MoveL Offs(pPick2,0,0,400),MinSpeed,z50,tGripWObj:=wobj0; ENDPROC PROC rPlace1() rPosition1; MoveJ Offs(pPlace1,0,0,400),MidSpeed,z50,tGripWObj:=wobj0; MoveL pPlace1,MinSpeed,fine,tGripWObj:=wobj0; Reset doGrip; WaitTime 0.3; GripLoad LoadEmpty; MoveL Offs(pPlace1,0,0,400),MidSpeed,z50,tGripWObj:=wobj0; MoveJ Offs(pPick1,0,0,400),MaxSpeed,z50,tGripWObj:=wobj0; nCount1:=nCount1+1; IF nCount120 THEN bPalletFull1:=TRUE; ENDIF ENDPROC PROC rPlace2() rPosition2; MoveJ Offs(pPlace2,0,0,400),MaxSpeed,z50,tGripWObj:=wobj0;
