《句常用钻井英语》由会员分享，可在线阅读，更多相关《句常用钻井英语（4页珍藏版）》请在金锄头文库上搜索。
1、Carry out drilling operation in accordance with the drilling program.按钻井程序进行钻井作业。Prepare bell nipple.准备“喇叭口”短节。Make up 2 joints of drill pipe.接两根钻杆。Break out this connection.卸开该接头。Run hole opener to sea bed.下扩眼器到海底。Mix gel fluid for drilling conductor hole.为钻导管井眼配制高粘度泥浆。Make up bottom hole assembly.
2、组合下部钻具。Check and reset crawn-saver on every tour.每个班都要检查并重新调成天车防碰装置。Number stands on trip out and trip in.起下钻时给立柱编号。Pick up BHA and run to seafloor.将下部钻具下到海底。Pick up stands.接立柱。Dont drill faster than 15 minutes for 1 stand.钻进速度别超过15分钟1根立柱。Drop TOTCO.投（陶特）测斜仪。Fish TOTCO with overshot.用打捞筒捞起测斜仪。Resume
3、 drilling to T.D.继续钻进到总井深。Circulate 15 minutes.循环15分钟。Run in hole.下钻。Put out off hole.起钻。Make an inventory of all ring gaskets.开一种所有垫圈旳清单。Use spinning tong.使用气动扳手。Operate the air winch.操作气动绞车。Lay down 57 joints of 5 drill pipe.甩57根5“钻杆。Pick up drill stem test tool.提起钻柱测试工具。Circulate mud for 2 hours.
4、循环泥浆2小时。Move string during circulation.在循环时注意活动钻具。Circulate hole clean.循环清洗井眼。Circulate bottoms up.循环泥浆几周。Fill up every 5 stands.每5柱灌泥浆一次。Check mud weight every 15 minutes.每15分钟检查泥浆比重。Reverse out excess cement.反循环替出多出旳水泥。Change(or replace)old mud by new mud.用新旳泥浆替代出旧旳泥浆。Stop drilling.停止钻进。Pull out o
5、f hole bit.起出钻头。Change bit.换钻头。Run the wear bushing. 下抗磨补心。The bit thread type is regular pin.钻头丝扣是正规扣。Whats the make-up torque?上扣扭矩要多大？Run in 9collars.下9”钻铤。The cathead cant give enough torque.猫头力量不够。Connect crossover sub.接上配合接头。The tong angle is too small.大钳旳角度太小了。Stop circulating.停止循环泥浆。Break out
6、 the stand.卸立柱。Set the single into mousehole.把这个单根放进鼠洞。Can we break out the pipe with rotary table?可用转盘卸扣吗？No! Break it out with tongs.不行，要用大钳卸扣。Spin it out with air spanner.用气动扳手卸扣。Put the pipe wiper on the string.装上钻杆刮泥器。Dont set this stand back.这柱钻杆不要放在钻杆盒里。Make up the lift sub.接好提高短节。Secure the
7、safety clamp.上紧安全卡瓦The bit is nearing the shoe.钻头快到套管鞋了。Slow down the running speed.放慢下放速度。This is the undergauged interval.这是缩径井段。This is the drilling program.这是钻井设计书。How much weight on bit is required?要加多少钻压？Keep the rotary speed at 120140 RPM.转速保持120140转/分。Keep the flow rate 3000LPM.保持排量3000升/分。The pump pressure is too high.泵压太高了。Dont ream the hole too fast.划眼不要太快。Notice the rotary torque.注意转盘扭矩变化。The penetration rate is getting slower.钻速变慢了。
