《完整的一套产品检测标准英文Word文档》由会员分享，可在线阅读，更多相关《完整的一套产品检测标准英文Word文档（29页珍藏版）》请在金锄头文库上搜索。
1、MTL/ SGS TEST LIST (1)(Seating)(Combines Adult and Childrens sizes,:Chairs, Barstools, Ottomans,)Quality test standard/methodCriteria（标准）Results1.labeling / Design/Features（标签/设计特点）The actuality must keep consistency（一致性） with the claim（规定）.2.Instructions指示 说明Shall be included if necessary. Shall in
2、clude assembly, mounting（装备）, use, maintenance（维护）, cleaning and safety information as required in the language(s) applicable to the destination（目的地） country(s) with no errors or spelling mistakes.（地名写错） Shall be easy to follow and accurate.3.product size/weight产品尺寸 重量Report actual. Shall comply wit
3、h any claims (-0%, +3%)4. Costco Plastic Bag Warning StatementIf plastic bags (of any thickness) with a perimeter(周长) of 14 inches or greater are used in inner packaging, the following warning statement must be printed on at least one side of each bag in English, French and Spanish:5. Lead In Surfac
4、e Coating（被复盖）Shall not exceed 600 ppm (0.06% by weight) total lead6. Workmanship（工艺）/ Level No major defects（缺陷）。 No components（成分） missing, malformed（畸形的） or fractured （破裂） No hardware missing Smoothly ground welds（接合）, not over-ground and free of pits（凹陷） and splatter（说话结巴） No burrs（喉音） No loose
5、components and unsecured fastening where rigidity（硬度） is required In the case of wood (e.g. laminates（薄板) proper and uniform（一致的） adhesion（支撑） No scratches, dents（凹痕）, cracks（裂缝）, marred（损坏） or discolored surface In the case of molded plastic, consistent and concise form and no defects evidencing（明显
6、的） of overuse（过度的） of mold。 Finished edges and seams（衔接口） Accurate and consistent（调和的） painting Components even in color, uniform clarity All seams and components in even alignment（结盟） Accurate and consistent painting Components even in color, uniform clarity（清楚）7. Sharp Points and EdgesShall have n
7、o sharp edges or sharp points on any component other than those required for functional use.8. Cross Cut AdhesionPlating / finish must stay affixed using a utility（万能）knife, cut a grid of 16 squares. Use 3M masking tape (#202), apply to the grid. Remove to see if plating / finish remains intact.（完整无
8、缺）9. Flammability（可燃性） of Upholstery MaterialsMust comply with California Bureau of Home Furnishings Bulletin 116/11710. Finger EntrapmentShall meet the requirements intended to eliminate （消除） the possible hazard （危险） that may be caused by changing clearances or permanent（永久的） entrapment and pinchin
9、g（收宿）of fixed openings.(13mm)11. Resistance To Hot WaterPour 25 mL. of boiling water and allow cooling. Dry surface, Shall be no graying（灰色） or spotting（斑点）11 Effects Of Extreme Temperature24 Hours At -32 F And 140F - No failure12. Resistance（抵抗力） To Corrosion（侵蚀） (Metal Components)Shall withstand（抵
10、挡） 24 hours in 1% salt spray (fog) with no corrosion or visual change.13. Effects Of Humidity（湿度）No change after 24 hours. 95% RH & 100F14. Stain（污点） Resistance- (Do not test on picnic table/ benches/stora.ge racks)Various food materials should resist permanent staining.( After 2 hours, remove)1. Fr
11、enchs Mustard t/2. Heinz Ketchup/3. Ragu Spaghetti sauce (original)/4. Folgers Instant Coffee/ 5. Welchs Grape Juice/6. Kraft BBQ Sauce (original) / Red Wine 15 Resistance to Scratching / Marring Other SurfacesNo scratching or marring of surface (3 cycles of 6” back and forth.) Conduct with and with
12、out levelers. Note if levelers become bent or come off. Note any damage / defects (bent/broken levelers)16. Caster Performance (If Supplied)Max 5 lb pull to move under 200 lb load17. Rear Stability背后的稳定性Min 35 Lbs. (30 Lbs. children) tipping force with a 173 Lbs. (100 Lbs. children) weight placed on
13、 the seat (Strap). Force is applied in rearward direction against 1inch obstruction. Report result when seat is in minimum, midpoint and maximum position18. Front Stability(Excludes（把 除外） Barstools & Ottomans)The chair is obstructed（阻塞） by 1 inch bar in the front base, tipping force is measured in t
14、he 45 to the test platform. The tipping force shall not be less than 40% of the total chair weight.19. Tip Resistance (Stools Only)Min 10 degree with 150 Lbs. (Children 100 Lbs.) distributed load, no tip-over20. Stability (Stools Only)Min 20 Lbs. pull force after 150 Lbs. (Children 100 Lbs.) distrib
15、uted load on the seat, no tip-over21. Base Durability（耐用力）No structural（结构的） failure or permanent（永久的） deformation（变形） under 400 Lbs. (225 Lbs. children) static （静力的） load for 60 minutes. For multi seatback positions, report result when seat back is in minimum, midpoint, and maximum positions for 20 minutes each.22. Front Seating Capability(Excludes Barstools & Ottomans)No failure under 300 Lbs. (135 Lbs. children) loading at edge (6 In.)23. Impact（碰撞） Durability (*If applicable perform with and without cushion（垫子）)No structural breakage, max inch de
