《din en 586-3_englisch》由会员分享，可在线阅读，更多相关《din en 586-3_englisch（55页珍藏版）》请在金锄头文库上搜索。
1、ICS 77.150.10 Aluminium und Aluminiumlegierungen Schmiedestcke Teil 3: Grenzabmae und Formtoleranzen European Standard EN 586-3 : 2001 has the status of a DIN Standard. A comma is used as the decimal marker. National foreword This standard has been prepared by CEN/TC 132 Aluminium and aluminium allo
2、ys (Secretariat: France). The responsible German body involved in its preparation was the Normenausschuss Nichteisenmetalle (Nonferrous Metals Standards Committee), Technical Committee Schmiedevormaterial und Schmiede- stcke. Amendments DIN 1749-3 and DIN 1749-4, January 1974 editions, and DIN 17606
3、-3 and DIN 17606-4, December 1973 editions, have been superseded by the specifications of EN 586-3. Previous editions DIN 1749-3: 1963-05, 1974-01; DIN 1749-4: 1963-05, 1974-01; DIN 9005: 1941-08; DIN 9005-2: 1959-04; DIN 9005-3: 1959-04; DIN 17606-3: 1973-12, DIN 17606-4: 1973-12. Ref. No. DIN EN 5
4、86-3 : 2002-02 English price group 17Sales No. 1117 05.02 DEUTSCHE NORMFebruary 2002 EN 586-3 Continued overleaf. EN comprises 53 pages. No part of this standard may be reproduced without the prior permission of DIN Deutsches Institut fr Normung e.V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany
5、, has the exclusive right of sale for German Standards (DIN-Normen). Aluminium and aluminium alloys Forgings Part 3: Tolerances on dimensions and form English version of DIN EN 586-3 Supersedes DIN 1749-3 and DIN 1749-4, January 1974 editions, and DIN 17606-3 and DIN 17606-4, December 1973 editions.
6、 Nur zur Information. Wird bei nderung nicht ausgetauscht. Vervielfltigungsrecht nach DIN Merkblatt 3 Oerlikon Leybold Vakuum GmbH English version ICS 77.150.10 Aluminium and aluminium alloys Forgings Part 3: Tolerances on dimensions and form 2001.CEN All rights of exploitation in any form and by an
7、y means reserved worldwide for CEN national members. Ref. No. EN 586-3 : 2001 E Aluminium und Aluminiumlegie- rungen Schmiedestcke Teil 3: Grenzabmae und Formtoleranzen This European Standard was approved by CEN on 2001-09-30. CEN members are bound to comply with the CEN/CENELEC Internal Regulations
8、 which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stand- ards may be obtained on application to the Management Centre or to any CEN member. The European
9、Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national st
10、andards bodies of Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. EN 586-3 October 2001 Management Centre: rue de Stassart 36, B-1050 Brussels
11、European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Aluminium et alliages daluminium Pices forges Partie 3: Tolrances sur dimensions et forme Page 2 EN 586-3 : 2001 2 3 3 4 5 6 6 6 6 7 7 9 9 23 28 53 Page 3 EN 586-3 : 2001 Page 4 EN 586-3 : 2001 Page
12、5 EN 586-3 : 2001 Page 6 EN 586-3 : 2001 Page 7 EN 586-3 : 2001 Page 8 EN 586-3 : 2001 Page 9 EN 586-3 : 2001 Page 10 EN 586-3 : 2001 Page 11 EN 586-3 : 2001 Page 12 EN 586-3 : 2001 Page 13 EN 586-3 : 2001 Page 14 EN 586-3 : 2001 Page 15 EN 586-3 : 2001 Page 16 EN 586-3 : 2001 Page 17 EN 586-3 : 200
13、1 Page 18 EN 586-3 : 2001 Page 19 EN 586-3 : 2001 Page 20 EN 586-3 : 2001 Page 21 EN 586-3 : 2001 Page 22 EN 586-3 : 2001 Page 23 EN 586-3 : 2001 Page 24 EN 586-3 : 2001 Page 25 EN 586-3 : 2001 Page 26 EN 586-3 : 2001 Page 27 EN 586-3 : 2001 Page 28 EN 586-3 : 2001 Page 29 EN 586-3 : 2001 Page 30 EN
14、 586-3 : 2001 Page 31 EN 586-3 : 2001 Page 32 EN 586-3 : 2001 Page 33 EN 586-3 : 2001 Page 34 EN 586-3 : 2001 Page 35 EN 586-3 : 2001 Page 36 EN 586-3 : 2001 Page 37 EN 586-3 : 2001 Page 38 EN 586-3 : 2001 Page 39 EN 586-3 : 2001 Page 40 EN 586-3 : 2001 Page 41 EN 586-3 : 2001 Page 42 EN 586-3 : 2001 Page 43 EN 586-3 : 2001 Page 44 EN 586-3 : 2001 Page 45 EN 586-3 : 2001 Page 46 EN 586-3 : 2001 Page 47 EN 586-3 : 2001 Page 48 EN 586-3 : 2001 Page 49 EN 586-3 : 2001 Page 50 EN 586-3 : 2001 Page 51 EN 586-3 : 2001 Page 52 EN 586-3 : 2001 Page 53 EN 586-3 : 2001
