《外文翻译(齿轮参数化设计及弯曲强度有限元分析)》由会员分享，可在线阅读，更多相关《外文翻译(齿轮参数化设计及弯曲强度有限元分析)（9页珍藏版）》请在金锄头文库上搜索。
1、Analysis based on the ANSYS metal gears and plastic gears inherent vibration characteristics compared姓名：班级：Abstract: Using ANSYS software gear finite element model, modal analysis, the plastic gear gun and steel gear module .State of natural frequencies and mode shapes diagram, were analyzed. The co
2、nclusion for the dynamic design of gears and gear structure related equipment fault diagnosisOff basis.Key words: plastic gear steel gear gun modal analysis of vibration characteristics0 Introduction The gear drive is the most important in the mechanical transmission drive gear transmission because
3、of its high efficiency, compact structure, the transmission ratio stable and are widely used in engineering. Accelerated due to the development of high-performance engineering plastics, the proportion of the application process for plastic and steel, plastics in the field of mechanical engineering i
4、s increasing, the production of gear materials are no longer limited to metallic materials, has grown to the plastic gear. On the application and theoretical study of the plastic gears, and steel gear, late research time is also shorter, and domestic and foreign researchers on the understanding of t
5、he plastic gear performance and application very immature, but to imitate and improve on the basis of the steel gear. Therefore, the experimental study of plastic gear is necessary. Plastic material with Bo, the elastic energy, and thus has obvious noise reduction and vibration damping performance.
6、In fact, for the transmission of power in terms of gear when the gear bodys natural frequencies and the frequency of exciting force is very close to the even drill the plastic material gear also have a resonance and noise 2 4321-437A. Therefore, during the plastic gear design, the vibration characte
7、ristics of the study is necessary. We use ANSYS software to gear finite element model, modal analysis, mode shapes and natural frequency of the plastic gears and alloy gear to provide a basis for the structural design and optimization of gear.1 A gear modal analysisModal analysis is used to determin
8、e the natural frequency of the vibration characteristics of structures or machine parts in the design and mode shapes. Withstand dynamic bearing load structure design parameters 3 4321-4324. Finite element analysis software ANSYS, modal analysis is a linear analysis of prestressed structure and cycl
9、ic symmetry structure modal analysis, modal analysis process is divided into four steps: modeling, loading and solving, extended modal and results post-processing. 1.1 gear finite element modelANSYS provides three kinds of ways: to generate a model generation method with ANSYS to create solid model,
10、 the model established by the input model system. The direct generation method suitable for small, simple model, the leaders of the other systems if the model is not suitable for meshing, requires a lot of repair work. Gear model is relatively complex, suitable for solid modeling method. Known by th
11、e finite element theory, the solid model can not be directly used for finite element calculation, so take it mesh to generate a finite element model, the mesh will directly affect the accuracy of the finite element calculation results .Define the element type for the Structural solid Brick 2 ( node
12、95, the input gear parameters, create the key points, connecting key points generated gear contour, gear tooth surface generated by the contour, surface generation bodies drag along the segment, showing a single tooth geometric mode J, division of a single tooth mesh gear is the structure of the bod
13、y of the loop extension cycle to generate the finite element model of the plastic gears in Figure 1 shows, the finite element model of the number of nodes on a single tooth 3f tS8 . unit number 1994.1.2 gear finite element model of the moldState analysisModal analysis of ANSYS, you must specify the
14、elastic modulus EX. ANSYS11.0 seven kinds of modal extraction method: the Block Ianczoe (block, t the sos France), Subspace is (subspace method) IowerDvnamics (source of power law), Reduced (reduction method), Un2symmetric (non-symmetric France), the Dam Network (damping France), QRDam network (Qlt
15、damping method). In this article to Block lanczos method to extract modal. Gear model is built, its modal analysis, modal analysis of the gear. Purpose is to find the order natural frequency of the gear and its corresponding vibration mode, and therefore does not need to load, only degrees of freedo
16、m constraints. Constraints: the gear inner hole circle cylinder constraint: s:. Set of modal extraction method for the Block Canczos France, set up to extract the number of modes of 5 want to get the unit to solve the results need to open the calculate elem re-salts, the frequency range specified modal extraction 0 100 000, specify the mode state extraction method, ANSYS automatically select the appropriate equation solver.
