《controwavered硬件》由会员分享，可在线阅读，更多相关《controwavered硬件（37页珍藏版）》请在金锄头文库上搜索。
1、1Controlwave RED Include: Baseplate Two CPU Module Two Power Supply/Sequencer Module CPU & Comm. Redundancy Switch Module Chassis AssemblyRemote I/OControlwave redundantControlWave I/O Expansion Racks2冗余控制器 低能耗、体积小 中央处理单元、电源模块及通讯的冗余 自动故障检测 自动切换到热备份控制器 高可靠性. 报警和历史数据的备份. 易用 组态方便.3ControlWaveRED Backpl
2、ane Assembly45Power Supply/Sequencer Module6PSSB Bd. Terminal Block Connector TB2TB2 provides 5 input connections for bulk power:TB2-1 = (+VIN) (+10.6V to +20V dc for +12V supply) (+20.7V to +30V dc for +24V supply)TB2-2 = (+VINF) Field Supply - Not UsedTB2-3 = (-VIN) (1st Supply Ground)TB2-4 = (-VI
3、NF) (2nd Supply Ground) - Not UsedTB2-5 = Chassis Ground - CHASSIS PSSM LEDs PWRGOOD(power good: green), MC (master clear active: red) Reset键按或上电的瞬间是灯亮 PWRDOWN (power fail: red).7PSSB Bd. Terminal Block Connector TB1TB1 provides 2 watchdog MOSFET switch connections:TB1-1 = VO - Watchdog MOSFET Switc
4、h OutputTB1-2 = VI - Watchdog MOSFET Switch InputTB1-3 = Not UsedWatchdog MOSFET Switch Field Wiring 8CPU Block Schematic910CPU Board Connector Summary1112CPU Module LEDs13RUN/REMOTE/LOCAL Switch RUN：禁止程序调试、程序下载等 LOCAL：用于串口就地通讯时 REMOTE：用于IP口或openBSI下载程序System Battery(3.6V 950mA/hr lithium) 供电：real-t
5、ime clock, CMOS RAM SRAM. 时间：4524小时 CPU Module Memory FLASH Memory(4M-64M)Static RAM Memory (2M-4M SRAM)FLASH BIOS Synchronous Dynamic RAM (4M SDRAM)1415161718Assignment of CPU Bd. Switch SW1 - User Configurations1.Note: Most SW1 switches should be ON, but SW1-6 MUST be OFF to enable redundancy, and
6、 SW1-7 must be set ON if this is the “A“ CPU, or OFF if this is the “B“ CPU.2.Note: System “A” CPU must reside in Slot #2 and System “B”CPU must reside in Slot #4. 19Assignment of CPU Bd. Switch SW3SCB Port Switches SW1 = COM3 & SW4 = COM4Note: Leave all SW3 CPU switches in default OFF position, exc
7、ept for #4.20COM1, COM2 & COM4 (SCB) Connector Pin AssignmentSCB Connectors J2 (COM3) Pin Assignment21Bristol Babcock 基于586的处理器 AMD Elan 520 - 100 MHz 32 bit CPU 多达三个100MB以态网口 控制网, 远程I/O网. 终合网络 多达四个串口 RS 485 光电隔离 带以太网口的远程I/O 三级权限设定 宽温度范围 (-40 to +70 ) 防爆CE, c/UL Class I, Div. 2 特点CPU22Front View of
8、CPU & Comm. Redundancy Switch Module23CCRSM: COM1 through COM4 Connector Pin AssignmentNote: RS-485 Signals in Table 2-3 are only available on COM3 & COM4.24两线制485：如接I/O卡件时485+接CW的TXD+或RXD+，485-接TXD-或RXD- 25A/B Primary Controller Select Switch - 2-position - selects the primary controller, i.e., CPU
9、 A (UNIT A) or CPU B (UNIT B) at CCRS Module power up only if the A/B EnabledMode Select Switch has been set in the automatic selection (centered) position. Theselected CPU Module will be chosen as the primary system controller if the CCRS Modules logic determines it is ready for on-line duty. Other
10、wise, the alternate CPU will be selected if it is OK.A/B Enable Key Switch - 3-position - used to determine whether the primary CPUselection is forced to CPU A (UNIT A) or CPU B (UNIT B) or is automatically selected(Center). Forced primary selection is useful for diagnostic purposes, where a failed
11、CPUModule may be placed on-line for debugging.26Front of CCRS Module :Connector J1 - Switched COM1 Port - 9-pin D-Type Male RS-232 - represents COM1 of the selected CPU Module.ConnectorJ2 - Switched COM2 Port - 9-pin D-Type Male RS-232 - represents COM2 of the selected CPU Module.Connector J3 - Swit
12、ched COM3 Port - 9-pin D-Type Male RS-232/485 - represents COM3 of the selected CPU Module.Connector J4 - Switched COM4 Port - 9-pin D-Type Male RS-232/485 - represents COM4 of the selected CPU Module.Connector J5 - CPU A Comm. Ports Intc. Cable Header - 2 x 25 Male, Shrouded & PolarizedConnector J6
13、 - CPU B Comm. Ports Intc. Cable Header - 2 x 25 Male, Shrouded & PolarizedConnector J7 - Isolated On-Line Status Outputs - 4-pin pluggable (Screw Clamp) - ProvidesA & B pairs of relay driven Normally Open (NO) & Common (COM) outputs27CCRS Module Status LEDsUNIT A ON-LINE LED - Green - ON means CPUA
14、 is on lineUNIT A FAIL LED - Red - ON means CPUA has failed - If blinking means CCRSSlot A cable is not attached or is defectiveUNIT B ON-LINE LED - Green - ON means CPUB is on lineUNIT B FAIL LED - Red - ON means CPUB has failed - If blinking means CCRSSlot B cable is not attached or is defectivePO
15、WER SYSTEM STATUS LEDs A & B - Red/GreenON Green means Power is goodON Red means Power is defective282930Point-to-Point 10Base-T Ethernet Cable 31Standard 10Base-T Ethernet Cable (CPU Module to Hub)32Ethernet 10/100Base-T CPU Module Pin Assignments33.扩展I/O机架结构网络交换机341.通讯CPU（扩展机架）352. CPU跳线设置363. 冗余I/O设置37
