《传动设备通过Profi-bus与WINCC的通讯》由会员分享，可在线阅读，更多相关《传动设备通过Profi-bus与WINCC的通讯（26页珍藏版）》请在金锄头文库上搜索。
1、 Automation and DrivesA&D Customer Service & Support2WinCC 通过Profibus 与Drive 通讯 必备备条件COM PROFIBUS 软件WinCC 组态编 程软件上位机中安装Profibus通讯卡, 如: CP5613,CP5611 Profibus 通讯电缆Profibus 总线联结 器Drive中有Profibus通讯模板 .如 : MASTER DRIVE 的CBP2通讯模板 , 标准变频 器的Profibus通讯模板 . Automation and DrivesA&D Customer Service & Support
2、31.运行 COM PROFIBUS 1. 运行 COM PROFIBUSAutomation and DrivesA&D Customer Service & Support41.设置主站的 Profibus 地址2.选择 主站类型 3.点击OK 进入下一步 121. 1 设 置 主 站(COM PROFIBUS)3Automation and DrivesA&D Customer Service & Support51.选择 Profibus DP 模式2.点击OK 进入下一步1. 2 设 置 主 站(COM PROFIBUS)12Automation and DrivesA&D Cust
3、omer Service & Support61. 在DRIVES中选择 从站类型2. 选择 从站通讯卡3. 选择 PPO类型 点击OK 进入下一步1. 3 设 置 主 站(COM PROFIBUS)1234Automation and DrivesA&D Customer Service & Support71. 设置 I/O 地址2. 点击OK 进入下一步1. 4 设 置 从 站(COM PROFIBUS)12Automation and DrivesA&D Customer Service & Support81. 将组态输 出为NCM 文件 , 文件扩展名 ,LDB11. 5 保 存
4、配 置(COM PROFIBUS)Automation and DrivesA&D Customer Service & Support92 运 行 Set PG/PC InterfaceAutomation and DrivesA&D Customer Service & Support102. 1 设置 PG/PC Interface (Set PG/PC Interface) 正确设置1. 2. 后 点击 Properties进入下一步12Automation and DrivesA&D Customer Service & Support11选择 COM PROFIBUS 中 组态时
5、生成的二进制文件 ( 参见 Section 1.5 ) 2. 2 设置 PG/PC Interface (Set PG/PC Interface) Automation and DrivesA&D Customer Service & Support123. 运 行 WinCC Automation and DrivesA&D Customer Service & Support133. 1 在Tag Management 中Add New Driver (WinCC) 121. 设右键点击 Tag Management2. 左键点击 Add New Driver 进入下一步Automatio
6、n and DrivesA&D Customer Service & Support143. 2 打开二进制文件PROFIBUS DP.CHN(WinCC) 121. 选择 PROFIBUS DP.CHN2. 左键点击 Open 进入下一步Automation and DrivesA&D Customer Service & Support153. 3 设置New Driver Connection 的属性 (WinCC) 1 231. 双击 PROFIBUS DP2. 右键点击 CP5412(A2)Board 13. 左键点击 NEW Driver Connection 进入下一步Autom
7、ation and DrivesA&D Customer Service & Support16点击 Properties进入下一步3. 4 设置New Driver Connection 的属性 (WinCC) Automation and DrivesA&D Customer Service & Support173. 5 设置New Driver Connection 的属性 (WinCC) 设置从站地址 必须与传动 装置中的一致点击进 入下一 步Automation and DrivesA&D Customer Service & Support18121. 右键点击 NewConne
8、ction 2. 左键点击 NEW Tag 进入下一步3. 6 设置New Driver Connection 的属性 (WinCC) Automation and DrivesA&D Customer Service & Support19点击进 入下一 步3. 7 设置Tag 的属性 (WinCC) Automation and DrivesA&D Customer Service & Support203. 8 设置Tag 的属性 (WinCC) 现在您已经可以在Driver 和 WinCC 之间交换数据了 Automation and DrivesA&D Customer Servic
9、e & Support214. Drive 中 的 设设 置v1.在 P918 中设置Profibus 地址 ,必须与 WinCC 中设置 相同 .地址不能重复 . v2. 控制字第十位置 “1” . PZD1 = W#16#X4XX .Automation and DrivesA&D Customer Service & Support22附 录录Automation and DrivesA&D Customer Service & Support23附 录录Automation and DrivesA&D Customer Service & Support24附 录录Automation and DrivesA&D Customer Service & Support25附 录录Automation and DrivesA&D Customer Service & Support26Customer Support
