《项目十二模具工图程绘制及材料选择》由会员分享，可在线阅读，更多相关《项目十二模具工图程绘制及材料选择（11页珍藏版）》请在金锄头文库上搜索。
1、项目十二 模具工程图绘制及材料 选择项目导入一相关知识 二项目实施 三Evaluation only.Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0.Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.Copyright 2004-2011 Aspose Pty Ltd.一一 项目导入项目导入模具工程图是由总装配图、零件图两部分 组成的。要
2、求根据模具结构草图绘制正式 装配图。所绘制装配图应能清楚地表达各 零件之间的相互关系，应有足够说明模具 结构的投影图及必要的剖面、剖视图。还 应画出工件图，确定模具材料、填写零件 明细表和提出技术要求等。Evaluation only.Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0.Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.Cop
3、yright 2004-2011 Aspose Pty Ltd.二二 相关知识相关知识（一）模具工程图的绘制 1 1模具总装配图的绘制模具总装配图的绘制（1 1）模具总装配图的绘制要求）模具总装配图的绘制要求 （2 2）模具总装配图的内容）模具总装配图的内容2 2模具零件图的绘制模具零件图的绘制 Evaluation only.Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0.Created with Aspose.Slides for .NET 3.5 Client Profile
4、5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.Copyright 2004-2011 Aspose Pty Ltd.1 1成型零件材料选用的要求成型零件材料选用的要求（1 1）机械加工性能良好）机械加工性能良好 （2 2）抛光性能优良）抛光性能优良 （3 3）耐磨性和抗疲劳性能好）耐磨性和抗疲劳性能好 （4 4）具有耐腐蚀性）具有耐腐蚀性（二）模具材料选用 Evaluation only.Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0.Cre
5、ated with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.Copyright 2004-2011 Aspose Pty Ltd.2 2注射模钢种的选用注射模钢种的选用（1 1）预硬钢）预硬钢 （2 2）镜面钢）镜面钢 （3 3）耐腐蚀钢）耐腐蚀钢 3 3国外模具材料概况国外模具材料概况（二）模具材料选用Evaluation only.Evaluation only. Created with Aspose.Slides for .NET 3.5 Client P
6、rofile 5.2.0.0.Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.Copyright 2004-2011 Aspose Pty Ltd.三、项目实施三、项目实施 （一）灯座模具总装图 （二）灯座明细表及模具材料 （三）灯座模具零件图 （四）绝缘胶架模具工程图范例Evaluation only.Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile
7、5.2.0.0.Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.Copyright 2004-2011 Aspose Pty Ltd.图12-1 灯座模具装配图Evaluation only.Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0.Created with Aspose.Slides for .NET 3.5 Client Pr
8、ofile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.Copyright 2004-2011 Aspose Pty Ltd.图12-2 脱浇口板Evaluation only.Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0.Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.Copyright
9、2004-2011 Aspose Pty Ltd.图12-3 定模板Evaluation only.Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0.Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.Copyright 2004-2011 Aspose Pty Ltd.图12-4 浇口套图12-5 限位杆Evaluation only.Ev
10、aluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0.Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.Copyright 2004-2011 Aspose Pty Ltd.图12-8 滑块Evaluation only.Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0.Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.Copyright 2004-2011 Aspose Pty Ltd.
