《jk单绳缠绕式提升机(e系列)主轴装置设计说明书毕业论文》由会员分享，可在线阅读，更多相关《jk单绳缠绕式提升机(e系列)主轴装置设计说明书毕业论文（50页珍藏版）》请在金锄头文库上搜索。
1、JK3 提升机(E 系列)主轴装置设计摘 要单绳缠绕式矿井提升机的工作原理：钢丝绳的一端用钢丝绳夹持固定在卷筒幅板上，另一端经卷筒的缠绕后，通过井架天轮悬挂提升容器。这样，利用主轴旋转方式的不同，将钢丝绳缠绕上或放松，以完成提升或下降容器的工作。主轴装置是单绳缠绕式矿井提升机的主要工作机构，它的作用是： (1)缠绕提升机钢丝绳；(2)承受各种正常载荷(包括固定载荷和工作载荷)；(3)承受各种积极情况所造成的非常载荷。在非常载荷作用下，主轴装置部分不应有残余变形。单绳缠绕式矿井提升机的主轴装置是其核心部件，要求我们应认真设计，精心制造，这对于确保矿井提升机安全可靠运行，预防和杜绝故障及事故的发生
2、，也具有十分重要的意义。本设计根据生产实际和预选的数据，以提升机的配套设备为核心，经过科学的计算和分析，设计、选择了一套矿井提升机的传动系统设备，并采用了光电测速传感器作为深度指示系统的数据采集装置，实现了从机械控制到数电控制的转变，同时为提升机控制系统的技术改造奠定了基础。关键词：提升机，主轴，制动器，光电测速传感器The designing of the main axle of JK-3 elevator (E system)ABSTRACTWhat the principle of the single rope twines mine pit elevator is that: On
3、e end of the steel wire rope is fixed to Winding by the steel wire rope nip, another end after twined hangs and promotes the vessel by derrick wheel. In this way, we make use of the differences of the revolve way to twine or relax the steel wire rope so that to complete the vessel to step up or drop
4、 down.Main axle is the core part of the mine elevator. Its functions are:(1) the steel wire rope of twines the type mine pit elevator ;(2) endure a kind of normal load( including fixed load and work load );(3) endure the kinds of unusual load which is result from positive situation. Under the unusua
5、l load function, the part of the main axle equipment should not remain remaining distortion. It required us to be careful designing and manufacture when designing and manufacturing. Only in this way, we can prevent the occurrence of failures or accidents. Obviously，the possesses is very significance
6、.This design is on the basis of the data which are chosen by advance and actually, take the elevator supplementary equipment as the core, after the analysis and computation in science, has designed and chosen a set of the transmission system of the mine pits elevators, and used the electrical-light
7、sensor as the equipment of the indicating system which to measure the amount of the depth of the tank. It enforced the change from the mechanically control to the numerical control, at the same time, has laid the foundation for improve the control system of the elevator.KEY WORDS：elevator, main axle
8、, brake, electrical-light measurement velocity sensor目 录前 言.1第 1 章 课题设计简介.21.1 设计课题.21.2 设计步骤.21.3 设计思路.2第 2 章 JK3 提升机 (系列)主轴装置的原始资料.32.1 本产品的型号、名称.32.2 本产品的性能指标和设计参数.3第 3 章 JK3 提升机（E 系列）的选择和设计.43.1 JK3 矿井提升机的工作原理和主要结构.43.1.1 主轴.43.1.2 卷筒.43.1.3 主轴承.53.1.4 盘形制动器装置.53.1.5 深度指示系统.63.1.6 减速器.63.1.7 联轴器.63.2 主轴装置的设计依据.73.2.1 钢丝绳.73.2.2 卷筒宽度 B.73.2.3 钢丝绳最大静张力 Fjmax.73.2.4 钢丝绳最大静张力差F.73.2.5 最大提升速度 Vmax.73.2.6 电动机功率 PN.83.3 主轴的选择.83.4
