《皮带运输机英文术语解释》由会员分享，可在线阅读，更多相关《皮带运输机英文术语解释（9页珍藏版）》请在金锄头文库上搜索。
1、 bimageConveyor terminology glossary If you have conveyor questions, contact Conveyors Direct A-B | C | D- E | F-H | I- L | M-O | P | Q-R | S | T | U- Z ACCUMULATING CONVEYOR: Any conveyor designed to allow collection (accumulation) of material. May be roller, live roller, belt and gravity conveyors
2、. ALLIGATOR BELT CLIP: Lacing attached to the belt with a hammer for the purposes of joining the ends of the belt together to form a continuous loop. AXLE: A non-rotating shaft on which wheels or rollers are mounted. BALL TABLE: A group of ball transfers over which flat surface objects may be moved
3、in any direction. BALL TRANSFER: A device in which a larger ball is mounted and retained on a hemispherical face of small balls. BED: That part of a conveyor upon which the load rests or slides while being conveyed. BED LENGTH: Length of bed sections only required to make up conveyor excluding pulle
4、ys, etc., that may be assembled at ends. BED WIDTH: Refers to the overall width of the bed section. BELT: A flexible band placed around two or more pulleys for the purpose of transmitting motion, power or materials from one point to another. BELT SCRAPER: A blade or brush caused to bear against the
5、moving conveyor belt for the purpose of removing material sticking to the conveyor belt. BELT SPEED: The length of belt, which passes a fixed point within a given time. It is usually expressed in terms of “metres per minute“. BETWEEN FRAME WIDTH: (BF) referred to as the distance between the conveyor
6、 frame sides on a belt conveyor, roller bed, live roller or gravity type conveyor. Also referred to as (BF) Between Frame. BOOSTER CONVEYOR: Any type of powered conveyor used to regain elevation lost in gravity roller or wheel conveyor lines. BRAKE MOTOR: A device usually mounted on a motor shaft be
7、tween motor and reducer with means to engage automatically when the electric current is cut off or fails. 页码，1/9Conveyors2009-11-5file:/C:Documents and Settings61023桌面皮带运输机英文术语解释.htmBRAKE ROLLERS: Air or mechanically operated brakes used underneath roller conveyor to slow down or stop packages being
8、 conveyed. Top CASTERS: Wheels mounted in a fork (either rigid or swivel) used to support and make conveyors portable. CEILING HANGERS: Lengths of steel rod, attached to the ceiling, from which conveyors may be supported to provide maximum utilization of floor space or when required height exceeds f
9、loor support capability. CENTRE DRIVE: A drive assembly mounted underneath normally near the centre of the conveyor, but may be placed anywhere in the conveyor length. Normally used in reversing or incline application. CHAIN CONVEYOR: Any type of conveyor in which one or more chains act as the conve
10、ying element. CHAIN DRIVE: A power transmission device employing a drive chain and sprockets. CHAIN GUARD: A covering or protection for drive or conveyor chains for safety purposes. CHAIN ROLLER CONVEYOR: A conveyor in which the rollers have attached sprockets which are driven by a chain. CHUTE: A t
11、rough through which objects are lowered by gravity. Can either be a slider bed or roller/wheel bed. CLEAT: An attachment fastened to the conveying surface to act as a pusher, support, check or trip, etc. to help propel material, parts or packages along the normal path of conveyor travel. CLEATED BEL
12、T: A belt having raised sections spaced uniformly to stabilize flow of material on belts operating on inclines. Cleats may be a part of the belt or fastened on. CLUTCH DRIVE: Drive used to disengage motor from reducer without stopping the motor or cutting the power. CLUTCH-BRAKE DRIVE: Drive used to
13、 disengage motor from reducer and stop conveyor immediately without stopping the motor or cutting the power. CONSTANT SPEED DRIVE: A drive with no provisions for variable A-B | C | D- E | F- H | I- L | M- O | P | Q- R | S | T | U- Z 页码，2/9Conveyors2009-11-5file:/C:Documents and Settings61023桌面皮带运输机英
14、文术语解释.htmspeed or a drive with the characteristics necessary to maintain a constant speed. CONVERGING: A section of roller or wheel conveyor where two conveyors meet and merge into one conveyor. CONVEYING SURFACE: Normal working surface of the conveyor. CROSS BRACING: Bars placed across the support
15、legs to aid in squaring of the frames. CROWNED PULLEY: A pulley which tapers equally from both ends toward the centre, the diameter being the greatest at the centre. Top DECLINE CONVEYOR: A conveyor transporting down a slope. DEGREE OF INCLINE: Angle of slope in degrees that a conveyor is installed.
16、 DISCHARGE END: Location at which objects are removed from the conveyor. DIVERGING: A section of roller or wheel conveying which makes a connection for diverting articles from a main line to a branch. DRIVE: An assembly of the necessary structural, mechanical and electrical parts which provide the motive power for a conveyor. DRIVE PULLEY: A pulley mounted on
