《(中英文对照)详细介绍弹簧拉力试验机的试验步骤》由会员分享，可在线阅读，更多相关《(中英文对照)详细介绍弹簧拉力试验机的试验步骤（3页珍藏版）》请在金锄头文库上搜索。
1、详细介绍弹簧拉力试验机的试验步骤详细介绍弹簧拉力试验机的试验步骤(中英文对照中英文对照)弹簧拉压试验机实验步骤Spring tension and compression testing machine experiment step弹簧拉压试验机专用于弹簧的检测，为了您能更好的使用机器，锐玛为您提供弹簧拉压试验机的详细试验步骤，希望对大家有所帮助。Spring tension and compression testing machine dedicated to the spring testing, in order that you can better use the machine
2、, sharp, to provide you with the spring tension and compression testing machine detailed test procedure, and they hope to help everyone.I、接通电源翻开电源，使数码管显示为机械预热将机械预热2030min。I, open source connected to power, the digital tube display for mechanical preheating mechanical preheating 20 30min.II、工夫设置按“设置”
3、键，输入*年*月*日，工件号*兴，操作者代号*(注：此项中小数点无意义)。II, time is set according to the“ Settings “ button, enter the * * * * * * * * * * * *, the workpiece, Hing, operator code * * ( Note: the decimal point in a meaningless ).III、形态设置按“#/打印”键，实验机进人正常测试形态，此时实验力和位移均主动清零，上方显示器为位移显示，单元为 mm，下方显示器为实验力显示，单元为 N。III, morphol
4、ogy is set according to the“ # / print“ button, the experimental machine into the normal test form, the experimental force and displacement are active reset, display display unit for top displacement, mm, below the display as the experimental force display, unit N.单件测量开端Single measurement start 1)按查
5、验弹簧的自在长度，将起落座 6 升到相顺应的地位(即被测弹簧能放进两压盘之间或上下两挂钩之间)，用小手把将其固定在立柱12 上。1) according to the inspection of spring free length, will seat 6 litres to adapt position (i.e., a spring to be measured can be put into the two plate or between the upper and lower two hooks ), with a small hand to be fixed on the upr
6、ight post 12.2)把被测弹簧放鄙人压盘或挂在上下两挂两钩之间，按“P 清/1”键，将弹簧自重去失落。2) the spring to be measured in next plate or hang on hang hook between two two, press “ P / 1“ key, will spring to lost weight.3)扳动操作手柄 7 使上压盘和弹簧刚接触，按“F 清/0”键，使位移数码管全为零。3) by pulling the operating handle so that the upper plate and 7 spring co
7、ntacts, press “ F / 0“ key, the digital tube zero displacement.4)持续扳动操作手柄 7，对被测弹簧加力，当位移数码管显示的位移量到了弹簧的变形量时，力值数码管显示的力值，就是被测弹簧的实验力值。4) sustained by pulling the operating handle 7, measured on the spring force, when the displacement digital display displacement of the spring deformation, stress value of digital tube display the force value, is a spring to be measured experimental force value.版权声明：原文出自 http:/ 转载，参考 请注明出处！
