《灯饰检验标准》由会员分享，可在线阅读，更多相关《灯饰检验标准（8页珍藏版）》请在金锄头文库上搜索。
1、A. Inspection Standard(验货标准验货标准) General QA StandardPage 1 of 8Unless otherwise stated. QC should use the following sampling plan and AQL (Acceptable quality Levels) 除非客人有特别要求QC将采用下列AQL验货标准:Critical defect :0% Major defect :2.5% Minor defect :4.0%B. Drop Test Standard(试摔测试标准试摔测试标准) Drop test is appl
2、icable for all items. QC will select 3 master carton from the shipment hold the master carton 试摔测试适用所有ITEM,QC将从大货中抽取3箱做测试 in a horizontal position, pointing the testing panel to the concrete floor. 水平向地面进行做测试test will repeat the test for each of the six faces,3 sides and 1 corner of the master carto
3、n. 测试为六面,三条边,一个角 pls refer the following table for the appropriate height. 测试高度请参考如下表格Gross weight of master carton 外箱毛重 0 9.5 kgs 45.3 68 kgsHeight from bottom of master carton to floor 外箱底部离地面高度 30 inches 24 inches 18 inches 12 inches 8 inchesIf the damage rate exceeds 10%,QC will recommend the fa
4、ctory not to release the shipment and explore ways to modify the package, However, the final disposition decision should be made with our QC manager. 如果损坏率超过10%,QC将提出不放行货物并与工厂讨论如何修改方案.最终由QC经理决定.C. Shade “Styrene“ Standard(灯罩塑胶板标准灯罩塑胶板标准) Thickness of the “Styrene“ for lamp shade with shade size 5“x
5、10“x 7“ or below needs 0.33mm 灯罩尺寸5“ x 10“ x 7“或以下尺寸时,须用0.33mm厚的塑胶板. Thickness of the “Styrene“ for lamp shade with shade size 5“ x 10“x 7“ or over needs 0.35mm 灯罩尺寸5“ x 10“ x 7“或以上尺寸时,须用0.35mm厚的塑胶板. D. OPP Standard(OPP标准标准) Appropriate width of the OPP wrap should be used for different shade size.
6、Criteria for the shade after wrapped by theOPP wrap need to be:OPP包装的宽度会因灯罩尺寸不同而使用不同,标准灯罩包装OPP包装必须如下:1. Shade to be totally covered by the OPP wrap without loosed end, Shade need to look neat and tidily after wrapped and style of the shade could be clearly visible after wrapped. 灯罩OPP包装要紧不可松动,灯罩要保持干
7、净,能清楚的看见灯罩的类型. 2. No “excess crinkle“ of the OPP wrap on the top part of shade. 灯罩顶部不可以有过多的皱折.E. Lead Contents Standard(含铅量标准含铅量标准) all products must be used low lead contents requirement( 90PPM/0.009% Maximum), except other special requirement form other customers. 除非客户有其它的特殊要求.所有产品都必须使用低含铅量(0.009%
8、最高),.F. Plug Cover Standard(插头脚套标准插头脚套标准) Clear plug cover must to be used for all lighting products 所有燈類產品必须使用透明的插头脚套.General QA StandardG. Cord TIE UP Method (电线绑法电线绑法)Page 2 of 8All non-KD table lamp products must be follow with instruction to TIE UP the cord. Please refer below diagram 1 Bubble
9、表面有明显的凹痕或汽泡Page 7 of 8vvvvvvvvv vv vv vvvvvvvv vv vv vv vvvv vv vv vv v33343536General QA StandardFinger printings poor-significant/slight 手指印 Poor soldered/welded-Significant/ slight 电线头点锡不良或没有 Unstable/wobble base-Significant/ slight 底座不稳/摇晃 Missing part/ component 部份配件不见Page 8 of 8v vv vv vv3.0 P
10、ackage InspectionWrong barcode label1CR MA MIv23456789111213151617外箱标贴错误 外箱质量不好（如变形/破损/粘合不牢固/不成形/脏/褪色） 外箱封箱或热封不安全,要用2.25“宽的胶带封箱 Sharp tools in carton 有封利的工具在外箱内 Dampness-Significant/ Slight 外箱潮湿 Incorrect/incomplete/wrong carton marking 不正确/不完整/错误的外箱唛头 Poor printing, Not readable 包装印刷不良，不容易读 Export
11、Carton not properly numbered 出口外箱没有编写箱号 Drop test failed 试摔测试失败 Use of Wire, Staple Pin or Metal Straps (If it cannot be allowed) 用金属线,钉书钉,大头针接合包装箱(如果没有经过同意,不可以用). Packing too loose or too tight. 包装太松或太紧. Wrong placement of carton marking/ bar coded stickers. 外箱麦头位置印错,外箱标贴位置贴错. Insect inside carton
12、昆虫在外箱里面. The color box should fit size requirement, no print unhealthy, chromatism, dirty, humid. 彩盒尺寸正确,但印刷不好,有色差,脏/潮湿. Instructions Manual printed poor, not clearly, but can read. 说明书印刷不良/不清楚,但可以读. Instructions Manual printed wrongly at key processing/ not key processingvvvvv vv vv vvvvvvvv 18 说明书印刷错误,没有处理.v
