《协昌环保脉冲控制仪x8a6详细介绍》由会员分享，可在线阅读，更多相关《协昌环保脉冲控制仪x8a6详细介绍（6页珍藏版）》请在金锄头文库上搜索。
1、SXC-X8A6 在线电脑脉冲控制仪 SXC-X8A6 online pulse controller说明书 Manual 一 概述 IntroductionSXC-X8A6 在线电脑脉冲控制仪是一款控制电磁脉冲阀按次序依次喷吹的袋式除尘器用控制器。其性能可靠，使用寿命长，金属密封外壳可适用多种工况环境。SXC-X8A6 online pulse controller is used to control solenoid valve in turn for baghouse dust collector. It features reliable performance and long s
2、ervice life. The metal seal housing can be applicable to variety of working environment.型号标示MODEL标示代表含义 MEANING OF MODELSXC 公司代号：苏州协昌环保科技股份有限公司SUZHOU XIECHANG ENVIRONMENTAL PROTECTION TECHNOLOGY CO.,LTD.X 新式改进款 NEW MODEL8A 在线式脉冲输出系列 ONLINE PULSE CONTROL SERIES6 碳钢挂式外壳 HANGING STEEL HOUSINGNO. 最大回路数（
3、最多可控制的电磁脉冲阀数量）THE MAXIMUM NUMBERS OF SOLENOID VALVE TO BE CONTROLLED二 参数说明 Parameter indication参数 Parameter 参数值 Value 备注 Note输入电压 Input voltageAC220V（ 50/60HZ）输出电压 Output voltageDC24V工作电流 Current 1A额定功率 Power 8W脉冲宽度 Pulse duration2-255（10mS） 10mS 每单位可调Adjustable脉冲间隔 Pulse interval1-255S 1S 每单位可调Adju
4、stable循环周期 Cycle 0-255Min 1Min 每单位可调Adjustable输出回路 Channel 5/10/20/30/40 可调 Adjustable三 操作指南 Operation instruction1 显示说明 Display help：本机为三位数码管显示，运行状态时，数码管显示当前喷吹的回路；调整状态时，显示当前正在调整的参数值。This controller is three digital tube display. When in running state, the digital tube shows the current cleaning cha
5、nnel; When in adjusting state, the digital tube shows the adjusting parameters.2 指示灯 Indicator lamp：指示灯Indicator lamp运行状态时亮Lamp is on in running state调整状态时亮Lamp is on in adjusting state脉宽Pulse duration电磁阀打开Solenoid valve opens正在调整此参数值Adjusting this parameter间隔Pulse interval电磁阀关闭后等待间隔Solenoid valve c
6、loses, waiting for interval 正在调整此参数值Adjusting this parameter 周期 一个循环喷吹结束后等待周期至下一循环开始 One circular cleaning ends, waits to the next cycle 正在调整此参数值Adjusting this parameter回路Channel- 正在调整此参数值Adjusting this parameter电源Power supply工作电压正常Normal working voltage工作电压正常Normal working voltage3 参数调整 Parameter a
7、djustment：按键 Button 按键操作说明 Instruction复位Reset运行状态时，使用此键回到第一回路重新喷吹；调整状态时回到“脉宽”参数调整状态。When in running state, press this button to re-start the cleaning from 1st channel; when in adjusting state, press this button to return to “pulse duration” parameter adjustment. 运行/调整Run/Adjust运行状态时按住此键 2S 以上松开时切换到参
8、数调整状态；反之亦然。Press the button more than 2S and then undo the button in running state it will switch to parameter adjustment state; or vice versa.设置Set参数调整状态时切换需要调整设置的参数。Set up the parameters in adjusting state+ 参数调整时，使当前参数每单位递加。Increase the parameter value per unit- 参数调整时，使当前参数每单位递减。Decrease the param
9、eter value per unit复吹RB(Repeated Blowing)运行状态时，按住此键 2S，使其只喷吹当前回路，暂停循环；再按住此键 2S，切换回原运行循环中。Press the button for 2S in running state, it will clean only the current channel and pause; press the button again for 2S, it will switch to the original cycle.四 接线说明 Wire diagram端子名称 Terminal name 功能说明 Function
10、 descriptionL AC220 电源 L 接入端 L connection terminal of AC220V power supplyN AC220 电源 N 接入端 N connection terminal of AC220V power supply 地线接入端 Connection terminal of ground wireCOM 电磁脉冲阀公共输出端 Common output termical of solenoid valve1-20/40 电磁脉冲阀 1-20/40 回路信号输出端Output terminal of 1-20/40 channel of sol
11、enoid valveYCGND压差干接点( 选配)Dry contact of pressure differential (Optional)五 安装外形尺寸 Install size（LHW=230mm190mm96mm）六 注意事项 Notes此仪器需要专业人员进行操作，切勿随意通电或调整参数，以防损坏给您带来不便。且不能在未经本公司允许下自行插拔排线，拆装线路板或电子元器件。This equipment requires professional personnel to operate, DO NOT power on or adjust the parameters casually so as not to bring you any inconvenience. DO NOT insert/draw the wires or assemble the PCB or electronic components without company permission.
