《中厚板英语词汇》由会员分享，可在线阅读，更多相关《中厚板英语词汇（31页珍藏版）》请在金锄头文库上搜索。
1、 第二章 宽厚板轧机词汇 2.1 （机械部分）2.1.1 AAbort escape system 紧急逃逸系统Abort handle 应急把手Abrasion resistant 抗磨的 ,耐磨的Absorption of moisture 吸湿，吸潮Abrupt change 急剧 突然变化Acceleration ramp 速度爬升，加速斜坡Accumulator 活套Acid resistant 耐酸的Acoustic baffle (damping; enclosure; panel; barrier) 声障板Actuator 执行机构Air inlet duct 空气入口管道Ai
2、r knife 气刀Air pocket 气穴Air damper 节气门Air cushion 气垫Air cooler 空气冷却器Allen key 艾伦内六角扳手Amplification factors 放大系数Anti-flutter roll 防振辊Anti crimping roll 抗皱轴AOD process 氩氧脱碳法Application software 应用软件Approach roller table 输入辊道Arithmetic mean value 算术平均值Armour plate 护板Articulated dummy bar 铰链引锭杆As-built c
3、onstruction drawing 建设竣工图纸Asynchronous motor 异步电动机Axial runout 轴向跳动Accelerated plate cooling equipment 快速冷却装置（ACC）Adjustment system (wedges) for the top and bottom rolls including Wedge cylinder 上下矫直机调整系统（斜锲）包括斜锲油缸Adjustment system for the entry and exit rolls 入口、出口矫直辊调整系统Agitator 搅拌器Air cylinder 气缸
4、Air pressure tank 空气压力罐Antifriction bearing 防摩擦轴承Anti-rusting coat 防锈涂层Apron 挡板，裙板Automatic valves 自动阀Manual valves 手动阀Motorized valve 电动阀Roller bearing 滚柱轴承2.1.2 B Backpressure 背压Backlash compensation 间隙补偿Backstop 托架，止回器Backup rolls 支撑辊Backup roll assembly 支撑辊装配总成, Backup roll bending 支撑辊弯曲 Backup
5、roll change (dismantle) stool 支撑辊更换（分解）托架Backup roll cleaning device (extractor) 支撑辊清理装置（提取设备）Backwash water 反冲水,回洗水Baffle plate 隔板, 挡板 Bag filter 袋式滤器Bag house 袋滤捕尘室Baling band 打包窄钢带Baling press 打包机Baling wire 打包钢丝铁丝Ball valve 球阀Bank of pumps 水泵机组排Bar coded label 条形码标签Bar mill 小型轧机Barrel hardness 辊
6、身硬度Base line 测基线Battery limit 界限，界区Battery power supply unit 电池供电机组Bayonet locking 卡口锁定Bearing chocks 轴承座Bearing clearance 轴承余隙Bearing extractor 轴承提取装置 Bearing end play 轴承的轴向间隙Bearing thrust 轴承推力，轴承止推Belt wrapper 助卷皮带Belt wrapper tucking arm 助卷皮带压臂Bending stress 抗弯强度Bifurcated launder 分叉流槽Bleed port
7、 泄放孔Block diagram 框图Block circuit 闭塞电路Bogie 小车Bolted connection 螺栓连接Booster pump 增压泵Booster fan 增压风机Bottom bending roller 下转向弯辊Bottom sump 废水坑Bottom-pour ladle 底流式钢包Bottom-tap ladle 底部放流钢包Bottom-roll motor 下轧辊马达Boundary friction 边缘摩擦Boundary lubrication 边缘润滑Clyburn spanner 活扳手Cock spanner 旋塞扳手Double
8、 spanner 双头螺丝扳Double-ended open-jawed spanner 双端开口爪形扳手Double offset ring spanner 梅花扳手English spanner 活动扳手Hammering spanner 单头开口爪扳手Hose spanner 软管扳手Inner hexagon spanner 内六角扳手Ratchet spanner 棘轮扳手Brace nut 拉紧螺帽Breakout 漏钢，烧穿Breakout warning system 漏钢报警系统Breakout predication system 漏钢预报系统Brinell hardne
9、ss test 布氏球印实验Bulk density 容积密度，单位容积重量Buried cable 直埋埋地电缆Butterfly valve 蝶形阀Bypass valve 旁通阀Back-up chocks 轴承座Back-up roll balancing 支撑辊平衡装置Back-up roll change rails 支撑辊换辊轨道Balancing cylinder & bracket 平衡缸及支架Bearing housing assembly 轴承组件Bed plates 地脚板Bending cylinders 弯辊缸Bending frame 弯辊框架Bottom kni
10、fe table 下剪刃台Brackets for hydraulic cylinder 液压缸支架Breast rollers 机架辊Bridging table for roughing stand 粗轧机过桥辊道Bucket car 废料斗小车Bumper 减震装置BUR balancing cylinder 支撑辊平衡油缸Bushing (spindle head holder) 轴瓦（扁头套保持架）Bushing and sliding liners 轴瓦和滑动衬板2.1.3 CCantilevered beam 悬臂Carryover moment 传递力矩Chain-type d
11、ummy bar 链式引锭杆Chock separator 轴承座分离器Chock tilter 轴承座翻转装置Chute roller table 滑行辊道Cobble bar kick-off device 废品钢筋清理装置Cooling header 冷却集管Cooling tower 冷却塔Crop shear 切头, 切尾剪Crop shear entry guide 切头剪进口导板Crow bar / Pry bar 撬杠Curb plate 侧板,转护板Curved apron plate 弧形挡板Cam 凸轮Carrier beam 框架梁Carry out table 过渡辊
12、Center guides 对中导板Central gear lube oil filling system 集中齿轮润滑油加油系统Central filling system for MORGOIL-oil 摩戈伊尔铝硅锡合金轴承集中加油系统Central fresh oil filling and waste oil collecting system 集中加油和废油收集系统Chasing tool （车）螺纹工具Chainways 链轮轨道Clamping rolls 夹紧辊Cold plate leveller entry table 冷矫入口辊道Conditioning bed 精整台架Cooling bed entry table 冷床入口辊道Cooling bed walking beam type 冷床步进梁 (CB)Counterweight 配重，对重 Cover for hydrosta
