《压力容器工程规定(中英文)》由会员分享,可在线阅读,更多相关《压力容器工程规定(中英文)(23页珍藏版)》请在金锄头文库上搜索。
1、压力容器工程规定Engineering Specification for Pressure VesselsC O N T E N T S目录1. GENERAL 概述1.1 Scope 范围 1.2 Codes, Standards and Regulations 规范、标准及规章 1.3 Units 单位1.4 Purchasers Drawing and Documents 买方图纸及文件1.5 Vendors Drawings and Documents 卖方图纸及文件1.6 Site Condition 现场条件2. DESIGN 设计2.1 Design Pressure 设计压力
2、2.2 Design Temperature 设计温度2.3 Corrosion Allowances 腐蚀余度2.4 Materials 材料2.5 Loading Conditions and Strength Calculation 负荷条件及强度计算2.6 Tolerances 允许偏差3. DETAIL DESIGN 详细设计3.1 Shells and Heads 容器壁及顶3.2 Internals 内件3.3 Nozzles and Manholes 设备口及人孔3.4 Bolts, Nuts and Gaskets 螺栓、螺母及垫片3.5 Supports 支架3.6 Mis
3、cellaneous 其它4. FABRICATION 制作4.1 Plate Layout 排板4.2 Forming 成型4.3 Welding 焊接4.4 Heat Treatment 热处理5. INSPECTION AND TESTS 检测及试验6. NAMEPLATE, PAINTING AND MARKING 铭牌、刷漆及标识6.1 Nameplate 铭牌6.2 Painting 刷漆6.3 Marking 标识7. PACKING AND SHIPPING 包装和运输7.1 General 概述7.2 Packing and Preparation for Shipping
4、包装与运输准备7.3 Shipping 运输Appendix A: Tolerance for Pressure Vessels 附 A:压力容器允许偏差1. GENERAL1.1 Scope1.1.1 This specification together with the engineering drawings covers the requirements for the materials, design, fabrication, inspection, testing and supply of pressure vessels used for CIBA SBR 3rd lin
5、e project inZhenjiang, the Peoples Republic of China.本规范及工程图纸包含对中国镇江 CIBA SBR第 3条线工程中使用的压力容器的材料、设计、制作、检测、试验及供应的要求。This specification shall be referred to also for the non-pressure vessels except for the requirements of local regulation if vessel shape is similar to pressure vessels.本规范也可用于外形与压力容器相同的
6、非压力容器。1.1.2 The definition of pressure vessels shall be in accordance with “The Pressure Vessels Safety Technology Supervision Procedures” in the Peoples Republic of China.压力容器的限定根据中国的“压力容器安全技术监督程序”进行。1.1.3 This specification does not apply, in general, to auxiliary pressure vessels which are attach
7、ed to turbines, engines, pumps, compressors and other mechanical equipment which are normally designed under the manufacturers standard.一般情况下,本规范不适用于涡轮、发动机、泵、压缩机及其它依照厂家标准设计制造的机械设备的附属压力容器。1.2 Codes, Standards and Regulations 规范、标准及规章1.2.1 Pressure vessels fabricated in China shall be designed, fabric
8、ated, inspected and tested in accordance with the requirements of the following codes, standards and regulations of the latest edition.中国制作的压力容器必须根据以下最新版的规范、标准及规章的要求进行设计、制作、检测及试验。(1) The Pressure Vessels Safety Technology Supervision Procedures (1999 edition)压力容器安全技术监督程序(1999 年版)(2) Steel Pressure V
9、essels GB1501998 钢制压力容器(3) Technical Specification for Fabrication of Steel Chemical Vessels HG20584-1998钢制压力容器制作技术规范(4) Steel Welded Atmospheric Pressure Vessels JB/T47351997 钢制焊接常压容器(5) Basic Specification for Steel Chemical Vessel Design HG20580-1998 钢制化学容器设计基本规范(6) Specification for Materials Se
10、lection of Steel Chemical Vessels HG20581-1998钢制化学容器材料选择规范(7) Specification for Stress Calculation of Steel Chemical Vessel HG20582-1998钢制化学容器强度计算规范(8) Specification for Structural Design of Steel Chemical Vessel HG20583-1998钢制化学容器结构设计规范(9) Technical Requirements for Fabrication of Steel Chemical Ve
11、ssels HG20584-1998钢制化学容器制作技术要求(10) Mechanical Agitation Equipment HG/T20569-94 机械搅拌设备(11) Mechanic Properties Test of Welding Specimen for Steel Pressure Vessels JB 4744-2000钢制压力容器焊接样品机械性能试验(12) Nondestructive Test of Pressure Vessels JB4730-2000 压力容器无损检测(13) Carbon Steel and Low Alloy Steel Forging
12、s for Pressure Vessels JB 4726-2000碳钢及低合金钢锻制压力容器(14) Stainless Steel Forgings for Pressure Vessels JB 4728-2000 不锈钢锻制压力容器(15) Seismic Protection Code for Petrochemical Equipment HG 3048-1996石化设备地震保护规范1.2.2 Vendor shall be responsible for making all aspects of materials, design, fabrication, inspecti
13、on and testing conform to the requirements of the specified codes, standards and local regulations.卖方负责根据指定的规范、标准和地方规章的要求提供材料、设计、制作、检测及试验。Where there are conflicts between the requirements in Purchasers drawings/specifications and the specified codes/standards or local regulations, the order of prec
14、edence shall be as follows:如果买方图纸/规范同指定的规范、标准或地方规章之间存在冲突,按以下先后顺序加以遵守:(1) Local regulations 地方规章(2) Engineering drawings 工程图纸(3) Engineering specifications 工程规范(4) Codes and standards 规范和标准In such a case, Vendor shall promptly refer the conflicts to Purchaser in writing to obtaining Purchasers instru
15、ction.在此情况下,卖方需及时书面告知买方以获得买方指示。1.3 Units 单位Unless otherwise specified, SI units shall be applied as the measurement system for the drawings and documents to be submitted. However, nominal sizes of piping components shall be in accordance with inch system.除非另有规定,图纸及文件中所提及的单位均为国际制。但是,管道部件的公称尺寸应符合英制1.4
16、 Purchasers Drawing and Documents 买方图纸和文件1.4.1 Purchaser will provide Engineering Drawing for each pressure vessel which contains such information as the shape, basic dimensions, estimated thickness and weight, design conditions, materials for primary parts, nozzle specifications, and details of internals as required by Vendor to accomplish his mechani