《轮机英语关联题题库整理91篇(带翻译)》由会员分享，可在线阅读，更多相关《轮机英语关联题题库整理91篇(带翻译)（67页珍藏版）》请在金锄头文库上搜索。
1、.Passage 1 （原题库第 1 篇）Valve drive mechanismThe valve drive mechanism commands the inlet and exhaust valves at the required timing.第 3 题 The valve drive mechanism consists of an inlet and exhaust cam follower (8) each suspended in a plunger of the tappet assembly (7), two tubular push rods (4) with ba
2、ll joints, two nodular cast iron rocker arms (2) suspended in a rocker arm bearing bracket, two yokes (5) and a yoke guide pins. See Fig. 4-1.The tappet rollers follow the cam profiles and transfer the movements through push rods to the rocker arms. 第 4 题 The rocker arms operate the inlet and exhaus
3、t valves through yokes (5).Lubrication for the rocker arms comes from the engines secondary oil supply manifold throughdrillings in the cylinder head and rocker arm bracket.第 2 题 The tappet assembly receives lubricating oil via channels in the engine block from the main supply manifold. For the roll
4、er and shaft, the oil is supplied through the guiding plunger.第 4 题 To compensate for heat expansion a clearance must exist between the rocker arm and yoke.第 1 题 All adjustments have to be done on a cold engine only.1. According to the Passage, the best time to adjust the valve clearance is _.A. bef
5、ore the engine is started B. when the engine is runningC. after the engine has just been stopped D. when something has gone wrong with the engine注：根据文章来看，调节阀间隙的最好时间是在发动机启动之前。2. The roller and the tappet assembly are lubricated by means of_.A. the main lube system B. the secondary oil systemC. the sp
6、ecial pumping system D. the turbine oil system注：滚轮和挺杆组件借助于主润滑系统润滑。3. According to the Passage, the valve drive mechanism does not include_.A. tappet rollers B. push rods C. nodular cast iron D. yokes and guide pins注：根据文章来看，阀驱动机构不包括球墨铸铁。 （包括挺杆滚轮、顶杆、吊梁和导销）4. To close valves tightly, which clearance sh
7、ould be inspected according to the maintenance schedule?A. The one between the cam and the tappet roller. B. The one between the push rods and the ban joints.C. The one between the rocker arms and the yoke D. The one between two tubular push rods.注：依据保养清单，要紧密的关闭阀件，应检查摇臂和吊梁之间的间隙。.Passage 2 （原题库第 3 篇）
8、Charge air coolerThe engine is equipped with a charge air cooler. The insert type charge air cooler is mounted in a welded casing (air trunk). The trunk is bolted to the engine block.第 1 题 Standard is a two-stage cooler mounted. The first stage, through which the charge air flows, is cooled with wat
9、er from the HT cooling system and cooks the charge air till approx. 90 100oC. The second stage is supplied with water coming from the LT water system and cooks the charge air further till the required temperature of approx. 50oC. 第 2 题(B)By controlling the water flow through the LT cooler the charge
10、 air temperature can be kept constant at the required temperature.The circulating coolant water should always be under positive pressure and should be as clean as possible. The operating air temperature should be maintained by controlling the coolant inlet temperature.Whilst the engine is running th
11、e air and coolant temperatures and pressures at inlet and outlet should be checked and logged periodically. 第 3 题 Variations from normal indicate faults developing such as fouling of the film plates or obstruction of the water tubes.第 4 题 Check daily, during operation of the engine, the working of t
12、he telltale hole at the free end of the charge air receiver. The function of this hole is to inform the operator the presence of water in the charge air receiver. Under normal condition only compressed air should escape from this hole.1. According to the Passage, the expression HT probably means_.A.
13、 HIGH TANK B. HIGH TEMPERATURE C. HEAT TRANSMISSION D. HEAT TRANSFER注：根据文章来看, HT的意思是：high temperature，高温。2. In order to maintain the change air temperature we should control_.A. the coolant inlet temperature coming from the first stage coolerB. the coolant flow coming from the second stage coolerC.
14、the coolant outlet temperature coming from the second stage coolerD. the coolant flow coming from the flint stage cooler注：为维持增压空气的温度，我们应控制来自第二级冷却器的冷却剂流量。3. The charge air temperature departing from normal may indicate that_.A. condensate can be formedB. only compressed air should escape from the tel
15、ltaleC. the film plates are becoming dirty or the water tubes are blocked by scaleD. cooling water may have been carried into the cylinders注：增压空气温度偏离正常表明镀膜变脏或水管被水垢堵塞。4. The function of the telltale hole is to_.A. detect whether compressed air has escaped from the holeB. control the coolant inlet tem
16、peratureC. determine whether the coolant water is under positive pressureD. inform the operator the presence of water in the charge air receiver注：警报孔或监视孔的作用是同志作业员扫气箱中有水。 telltale hole 监视孔，指示孔，警报孔； charge air receiver. 扫气箱Passage 3 （原题库第 6 篇）第 1 题 At the first start, listen carefully for possible jarring sounds. If anything is suspected, stop the engine immediately, otherwise stop the engine a
