《电器产品产品合格证中英对照》由会员分享，可在线阅读，更多相关《电器产品产品合格证中英对照（7页珍藏版）》请在金锄头文库上搜索。
1、产品合格证CERTIFICATE产品名称 Product name型号规格 Model 出厂编号 Serial no.出厂日期 leave factory date中 华 人 民 共 和 国苏州迪生电器有限公司Suzhou Disheng Electrical Appliance Co., Ltd. 结 论 Conclusion产品经检验，符合产品标准和技术条件规定的要求。The product is in line with the product standards and specified technical requirements.检验员 checker苏州迪生电器有限公司合格专用
2、章附注：Remark苏州迪生电器有限公司Suzhou Disheng Electrical Appliance Co., Ltd. DGCK，GGD2，GXL 例行（出厂）检验报告DGCK, GGD2, GXL routine (factory) inspection reports项目名称 Project Name 编号 NO. RD-8.3-03-01产品名称 Product Name： 型号规格 Model： 出厂编号 serial number：序号No.试验项目testing items标准要求 standards 测试设备testing device测试结果Testing resu
3、lts 备注remark1、电器元件应经过检验合格，有合格证明书。electrical components should be subject to inspection, with a certificate of compliance目测 visual2、安装的电器元件与设备表相符合。the installation of electrical components and devices table match目测 visual3、壳体及门的几何尺寸、焊接表面涂覆，电镀层符合规定要求。Dimension of shell and door welding surface coating
4、, electroplating layer meet requirements.目测 visual3m 钢卷尺3m steel tape4、接地、相序色标、联结、名牌数据正确无误。ground, phase sequence color, link, brand-name data is correct.目测 visual1一般检查General examination5、接地符号应明显，检查接地电路的联接性。grounding symbols should be clear, check the connection of the ground circuit目测 visual1、主电路各
5、带电部位与接地金属构件之间的电气间隙及爬电距离应不小于 20mm。electrical distance and creepage distance between the parts the main circuit and metal components ground should be not less than 20mm. 2、电气间隙 electrical distance10mm2 电气间隙爬电距 离3、爬电间隙 creepage distance12.5mm0-150mm 钢直尺 straight steel ruler1、任一可移开部件在同一规格的两个隔离室中各抽插 5 次，
6、检查互换情况，抽插应灵活。any parts can be removed in the same specification of the two isolation rooms inserted and taken out five times, check the exchange situation, inserted and taken out should be flexible.3手动操作试验互换性试验interchangeable test a manual test 2、手动操作部件操作 5 次，操作灵活无卡手动操作manual test滞现象。机械电气连锁有效。parts
7、be manually operated five times, operation flexible, no clamping stagnation. Mechanical electrical chain effective.4 通电操作 power operation通电操作 5 次，电器元件动作正常、仪表指示准确，符合装置的电气设计要求。 Power operation five times, electrical components work well, instrument instruction accurate, meet the electrical design requ
8、irements. 通电操作台Power console1、主电路与地之间 the main circuit and ground：2500V/1s2、主电路与各相之间 the main circuit and the phase：2500V/1s3、主电路与辅助电器之间 the main circuit and auxiliary appliance：2500V/1s4、辅助电路与地之间 the auxiliary circuit to ground：2500V/1s5工频耐压试验frequency voltage withstand test施加交流正弦50Hz 电压2500V，施压时间
9、1s 施压部位如下：voltage applied AC sinusoidal 50Hz 2500V, time 1s, position as follows:5、绝缘材料制造的外壳和手柄与带电部件及裸导电部件施加 1.5 倍电压。the insulating material of the shell and handle with live parts and bare conductive parts 1.5 times the voltage applied工频耐压试验台frequency voltage withstand test6保护电路连续性试验 protection cir
10、cuit continuity test金属安装结构与框架之间的紧固点应穿透不导电绝缘层，接地电阻应100m ，测量点不少于 5 处。测试电流 10A。the fastening points between metal mounting structure and frame should penetrate non-conductive insulation, grounding resistance should be 100m, measuring not less than five points. Test current 10A.测试仪 tester1、主开关电器在断开位置时两个
11、断口之间 when the main electrical switch is off, between the two fracture2、主开关电器在闭合位置时的不同极的带电部位之间。When the main electrical switch is on, between the live parts of different pole.3、主电路与控制电路之间。between the main circuit and control circuit.绝缘电阻仪Insulation resistance meter7绝缘电阻测量Insulation resistance measure
12、ment绝缘电阻应1k/V 测量部位如下insulation resistance 1k / V measurement position as follows:：4、各带电部件与金属框架之间。the live parts and metal frameworks.8外壳防护等级shell protection gradeIP30：用2.5mm 铜棒，施加 10N 外力，不能进入。IP30: with 2.5mm copper, applied 10N force, can not enter.试棒 Test bars判定结论 conclusion 日期 date测试人 tester 日期 d
13、ate苏州迪生电器有限公司Suzhou Disheng Electrical Appliance Co., Ltd. PZ30 例 行（出厂）检 验 报 告PZ30 routine (factory) inspection reports项目名称 Project name 编号 serial no. RD-8.3-03-02产品名称 product name：终端箱 terminal box 型号规格 model：PZ30- 出厂编号 serial number：序号No.试验项目testing items标准要求 standards 测试设备testing device测试结果Testing
14、 results 备注remark1、电器元件应经过检验合格，有合格证明书。electrical components should be subject to inspection, with a certificate of compliance目测 visual2、安装的电器元件与设备表相符合。the installation of electrical components and devices table match目测 visual3、壳体及门的几何尺寸、焊接表面涂覆，电镀层符合规定要求。Dimension of shell and door welding surface co
15、ating, electroplating layer meet requirements.目测 visual3m 钢卷尺3m steel tape4、接地、相序色标、联结、名牌数据正确无误。ground, phase sequence color, link, brand-name data is correct.目测 visual1一般检查General examination5、接地符号应明显，检查接地电路的联接性。grounding symbols should be clear, check the connection of the ground circuit目测 visual1、主电路各带电部位与接地金属构件之间的电气间隙及爬电距离应不小于 20mm。electrical distance and creepage distance between the parts the main circuit and metal components ground should be not less than 20mm. 2、电气间隙 electrical distance10mm2 电气间隙爬电距 离3、爬电间隙 creepage distance12.5mm0-150mm 钢直尺 straight s
